Specifications; Maintenance; Rh/Lh Front Door Latch Assembly-Renew; 0114Bd|Latch Assembly - Hood - Renew - Aston Martin V8 Vantage Workshop Manual

Handles and Lock Mechanisms (01.14)
Body System (01.00)

Specifications

Torque Figures
Description
Door handle
Latch

Maintenance

RH/LH Front Door Latch Assembly-
Renew
Repair Operation Time (ROT)
Item
Front Door Latch Assembly
Front Door Latch Assembly
Removal
1. Remove door trimboard assembly (see Workshop
Manual procedure 01.05.CB Trimboard Assembly -
Door - Remove for Access & Refit).
2. Remove glass regulator (see Workshop Manual
procedure 01.11.DA/01.11.DB Regulator - Door Glass ­
RH/LH - Renew).
3. Remove aperture seal from inside door.
4. Remove rear rubber cheater panel, fir tree trim pins
(x3), and inner glass seal.
5. Disconnect latch mechanism multiplug (x1).
6. Disconnect exterior door handle inner and outer cable.
7. Remove exterior door handle securing nuts (x3).
8. Loosen top nut (x1) and remove bottom nut (x1) from
key lock mechanism.
9. Remove door latch securing bolts (x3).
10. Feed interior latch handle cable through inner skin into
door interior.
11. Remove latch and keylock mechanisms carefully
through aperture.
Installation
1. Install latch and key lock mechanisms through door
aperture and feed interior door latch handle cable
through aperture.
2. Align door latch and secure with bolts (x3).
3. Align key lock mechanism and secure nuts (x2).
4. Refit exterior door handle and secure with nuts (x3).
5. Connect latch inner and outer cable to exterior door
handle.
6. Connect latch mechanism multiplug (x1).
7. Refit inner glass seal and rubber rear cheater panel, push
home fir tree trim pins (x3).
8. Refit door aperture seal.
9. Install glass regulator (see Workshop Manual procedure
01.11.DA/01.11.DB Regulator - Door Glass - RH/LH -
Renew).
1-10-2
10. Install trimboard assembly (see Workshop Manual
procedure 01.05.CB Trimboard Assembly - Door ­
Remove for Access & Refit).

0114BD|Latch Assembly - Hood - Renew

Nm
5
Repair Operation Time
9
Item
Hood Latch Assembly-Renew
Removal
1. Remove grille (see Workshop Manual procedure
01.08.AA Grille - Radiator - Renew
2. Remove slam panel (bolts x12).
Code
3. Remove bolts (x4) securing PAS oil cooler.
RH 01.14.CE
4. Remove bolts securing crossmember to inner wing (x4).
LH 01.14.CF
5. Remove bolts and spacers securing crossmember to
wing (x2).
6. Move crossmember to one side and lift up clear of
location (protect paintwork).
7. Disconnect bonnet latch multiplug.
8. Remove switch from latch body (to access cable).
9. Disconnect bonnet latch cable.
10. Remove bonnet latch from crossmember (screws x2).
Installation
1. Install bonnet latch to crossmember (screws x2).
2. Connect bonnet latch cable.
3. Install switch to latch body.
4. Connect bonnet latch multiplug.
5. Install crossmember (as removed).
6. Install bolts and spacers securing crossmember to wing
(x2).
7. Install bolts securing crossmember to inner wing (x4).
8. Install bolts (x4) securing PAS oil cooler.
9. Install slam panel (bolts x12).
10. Install grille (see Workshop Manual procedure 01.08.AA
Grille - Radiator - Renew).
RH/LH External Front Door External-
Renew
Repair Operation Time
Item
External Front Door Handle-Renew
External Front Door Handle-Renew
Removal
1. Remove door trimboard (see Workshop Manual
procedure 01.05.CB Trimboard Assembly - Door -
Remove for Access & Refit).
2. Release outer and inner cable from external door
handle.
3. Remove nuts (x3) securing external door handle to door
frame.
4. Manoeuvre and remove external door handle.
Workshop Manual
Code
01.14.BD
Code
RH 01.14.CJ
LH 01.14.CK
October 2005