Fuel Injection Pressure Sensor-Renew; Fuel Temperature Sensor-Renew; Fuel Injector Engine Set-Renew - Aston Martin V8 Vantage Workshop Manual

18. Refit heater hose (clipx2) and EGR vacuum lines (clips
x2) to bracket.
19. Install fuel feed pipe.
20. Install purge pipe p-clip.
21. Install harness bracket to engine.
22. Feed harness into inner wing area.
23. Install fusebox to bracket.
24. Install earth lead to fusebox.
25. Install battery lead to fusebox (1x nut and rubber cover).
26. Install multiplugs to fuse box.
27. Install fusebox bracket fixings.
28. Refit harness fir tree clips to cylinder head.
29. Refit engine breather hose.
30. Install VVT solenoid multiplug, position coil and CMP
harness (1x edge clip).
31. Install ECM (see Workshop Manual procedure 03.14.BB
XREF: 319 Engine Control Module - RH Renew
32. Install coil cover.
Installation LH Side
33. Connect breather hose to manifold (quickfit).
34. Connect IAT multiplug.
35. Unclip injector harness from cam cover (x2).
36. Connect injector multiplugs (x4).
37. Install pipe support bracket (nuts x2, bolts x2).
38. Install harness support bracket (bolt x1, nut x2) release
harness clips (fir tree x3).
39. Connect booster hose to manifold and support clip.
40. Connect heater hose from pipe (quick fit).
41. Install heater hose (x2) and throttle body hose (x2) from
support bracket.
42. Connect purge line to manifold and into support clip.
43. Connect breather hoses (x2) to cam cover.
44. Install coil cover.
45. Install corner cross brace (torque bolts with vehicle on
level ground).
Installation Not Handed
46. Refill coolant (see Workshop Manual procedure
03.03.AD Coolant - Drain & Refill).
47. Install cross brace (torque bolts with vehicle on level
ground).

Fuel Injection Pressure Sensor-Renew

Repair Operation Time (ROT)
Item
Fuel Injection Pressure Sensor-Renew
Removal
1. Depressurise fuel rail (see Workshop Manual procedure
10.01.EK Fuel System - Depressurise).
2. Disconnect vacuum hose.
3. Remove sensor from fuel rail (bolts x2).
4. Disconnect multiplug.
October 2005
Installation
1. Install sensor to fuel rail (bolts x2) (torque).
2. Connect multiplug.
3. Connect vacuum hose.

Fuel Temperature Sensor-Renew

Repair Operation Time (ROT)
Item
Fuel Temperature Sensor-Renew
Removal
1. Depressurise fuel rail (see Workshop Manual procedure
10.01.EK Fuel System - Depressurise).
2. Disconnect vacuum hose.
3. Remove sensor from fuel rail (bolts x2).
4. Disconnect multiplug.
Installation
1. Install sensor to fuel rail (bolts x2) (torque).
2. Connect multiplug.
3. Connect vacuum hose.

Fuel Injector Engine Set-Renew

Repair Operation Time (ROT)
Item
Fuel Injector Engine Set-Renew
Removal
1. Remove LH injectors (see Workshop Manual procedure
03.04.GH Injector - Fuel - LH Bank - Engine Set -
Renew).
2. Remove coils (see Workshop Manual procedure
03.07.HC Coil Assembly - Engine Set - RH - Renew).
3. Disconnect breather hose (quick fit) move aside.
4. Release harness fir tree clips (x3) from cylinder head and
move aside.
5. Remove fuse box bracket fixings (bolt & nut) (allows
movement).
6. Remove ECM (see Workshop Manual procedure
03.14.BB Engine Control Module - RH Renew).
7. Remove battery lead (1x nut and rubber cover) from
fuse box (2x leads).
8. Remove multiplugs (x10) from fusebox.
9. Remove earth terminal (1x nut &rubber cover) from
fusebox.
10. Remove fuse box from bracket (bolt x2).
Code
11. Release harness fir tree clips (x3) from engine bracket.
03.04.CB
12. Feed harness from inner wing and over engine to gain
access to cam cover.
13. Remove purge pipe p-clip (bolt x1) and move pipe
aside.
14. Remove harness bracket from engine (bolts x2, nut x1).
15. Release fuel feed hose from rail (clip x1) & move aside.
16. Disconnect heater hose from pipe (quick fit).
Workshop Manual
Fuel Charging System (03.04)
Code
03.04.DB
Code
03.04.FB
3-5-3