Aston Martin V8 Vantage Workshop Manual page 201

Brake Actuation System (06.06)
Brake System (06.00)
RH/LH Rear Brake Calliper Tube
Assembly-Renew
Repair Operation Time (ROT)
Item
Rear Brake Calliper Tube Assembly-
Renew
Rear Brake Calliper Tube Assembly-
Renew
Removal
1. Raise vehicle on ramp.
2. Remove road wheel(s).
3. Remove bleed nipple dust caps.
4. Fit bleed bottle to RHR/LHR calliper, open bleed nipples
(x1).
5. Fit bleed bottle to RHF/LHF calliper, open bleed nipples
(x1).
6. Depress brake pedal >60 mm and secure with support.
7. Tighten RHF bleed nipple, remove bleed bottle and fit
dust cap.
8. Tighten RHR/LHR bleed nipple, remove bleed bottle.
9. Remove screws (x5) securing LH/RH rear wheel arch
liner to body.
10. Ease wheel arch liner downwards to access brake tube
union.
11. Loosen and disconnect brake tube unions from LH in
line connection and RH brake hose connection.
12. Release brake tube from clips (x5) on subframe.
13. Manoeuvre and remove brake tube.
Installation
1. Install brake tube, connect unions (x2), secure brake
tube in clips (x5). Torque tighten unions.
2. Position wheel arch liner, install and tighten screws (x5).
3. Remove pedal support.
4. Top-up brake fluid.
5. Bleed brake calliper with assistance.
6. Remove bleed bottle.
7. Fit bleed nipple dust caps.
8. Clean off excess fluid.
9. Top-up brake fluid.
10. Install road wheel/s
11. Lower vehicle on ramp.
Brake Master Cylinder to Modulator
Secondary Tube Assembly-Renew
Repair Operation Time (ROT)
Item
Brake Master Cylinder to Modulator
Secondary Tube Assembly-Renew
Removal
1. Raise vehicle on ramp.
6-4-4
2. Remove road wheel(s).
3. Remove LH front wheel arch liner (see Workshop
Manual procedure 01.02.FB Wheel Arch Liner - Front -
LH - Renew).
Code 4. Remove bleed nipple dust caps.
06.06.BD 5. Position bleed container, connect bleed hose to LHR
calliper, open bleed nipples (x1).
06.06.BE 6. Position bleed container, connect bleed hose to LHF
calliper, open bleed nipples (x1).
7. Depress brake pedal >60 mm and secure with support.
8. Tighten LHR bleed nipple, disconnect bleed hose,
remove bleed container and fit dust cap.
9. Tighten LHF bleed nipple, disconnect bleed hose,
remove bleed container and fit dust cap.
10. Loosen and disconnect brake tube union from
modulator.
11. Loosen and disconnect brake tube union from master
cylinder.
12. Remove brake tube.
Installation
1. Install brake tube, connect and torque tighten unions.
2. Install LH front wheel arch liner (see Workshop Manual
procedure 01.02.FB Wheel Arch Liner - Front - LH -
Renew).
3. Remove pedal support.
4. Top-up brake fluid.
5. Bleed brake calliper with assistance.
6. Remove bleed bottle.
7. Install bleed nipple dust caps.
8. Clean off excess fluid.
9. Top-up brake fluid.
10. Bleed brakes (see Workshop Manual procedure
06.06.AD Pad Kit - Manual Brake and Clutch Pedal -
Renew
11. Install road wheel(s)).
12. Lower vehicle on ramp.
Brake Master Cylinder to Modulator
Primary Tube Assembly-Renew
Repair Operation Time (ROT)
Item
Brake Master Cylinder to Modulator
Primary Tube Assembly-Renew
Removal
1. Raise vehicle on ramp.
2. Remove road wheel(s).
3. Remove LH front wheel arch liner (see Workshop
Code
Manual procedure 01.02.FB Wheel Arch Liner - Front -
06.06.BF
LH - Renew).
4. Remove bleed nipple dust caps.
5. Position bleed container, connect bleed hose to LHR
calliper, open bleed nipples (x1).
Workshop Manual
Code
06.06.BG
October 2005