Rh/Lh Ignition Coil Cover-Renew - Aston Martin V8 Vantage Workshop Manual

Under Bonnet
8. Remove coils (see Workshop Manual procedure
03.07.HC XREF: 398 Coil Assembly - Engine Set - RH -
Renew
9. Disconnect breather hose (quick fit) move aside.
10. Release harness fir tree clips (x3) from cylinder head and
move aside.
11. Remove fuse box bracket fixings (bolt & nut) (allows
movement).
12. Remove ECM (see Workshop Manual procedure
03.14.BB Engine Control Module - RH Renew).
13. Remove battery lead (1x nut and rubber cover) from
fuse box (2x leads).
14. Remove multiplugs (x10) from fusebox.
15. Remove earth terminal (1x nut &rubber cover) from
fusebox.
16. Remove fuse box from bracket (bolt x2).
17. Release harness fir tree clips (x3) from engine bracket.
18. Feed harness from inner wing and over engine to gain
access to cam cover.
19. Remove purge pipe p-clip (bolt x1) and move pipe
aside.
20. Remove harness bracket from engine (bolts x2, nut x1).
21. Release fuel feed hose from rail (clip x1) & move aside.
22. Disconnect heater hose from pipe (quick fit).
23. Release heater hose (clips x2) and EGR vacuum line
(clips x2) from bracket.
24. Release harness from coolant pipe bracket (fir tree x3).
25. Disconnect EGR (x1), fuel rail pressure sensor (x1) and
injector multiplugs (x4), move harness aside.
26. Remove coolant pipe bracket (nuts x2 & bolts x2).
27. Disconnect EGR vac pipe from sensor and manifold,
move aside.
28. Remove cam cover (bolts x14).
29. Remove cam cover seals.
Installation
1. Install new cam cover seals, clean mating faces.
2. Install cam cover (bolts x14).
3. Connect EGR vac pipe to sensor and manifold.
4. Install coolant pipe bracket (bolt x2, nut x2).
5. Connect EGR (x1), fuel rail pressure sensor (x1) and
injector multiplugs (x4).
6. Refit harness to coolant pipe bracket (fir tree x3).
7. Connect heater hose to pipe (quick fit).
8. Refit heater hose (clips x2) and EGR vac lines (clips x2)
to bracket.
9. Install fuel feed pipe.
10. Install purge pipe p-clip.
11. Install harness bracket to engine.
12. Feed harness into inner wing area.
13. Install fusebox to bracket.
14. Install earth lead to fusebox.
October 2005
15. Install battery lead to fusebox (1x nut &rubber cover).
16. Install multiplugs to fuse box.
17. Install fusebox bracket fixings.
18. Refit harness fir tree clips to cylinder head.
19. Refit engine breather hose.
20. Install VVT solenoid multiplug, position coil and CMP
harness (1x edge clip).
21. Install ECM (see Workshop Manual procedure 03.14.BB
Engine Control Module - RH Renew).
22. Install coils (see Workshop Manual procedure 03.07.HC
Coil Assembly - Engine Set - RH - Renew).

RH/LH Ignition Coil Cover-Renew

Repair Operation Time (ROT)
Item
Ignition Coil Cover-Renew
Ignition Coil Cover-Renew
Removal
1. Open bonnet.
2. Remove ignition coil cover (clips x3).
Installation
1. Position coil cover and secure in clips (x3)
2. Close Bonnet.
Workshop Manual
Engine Sealing (03.10)
Engine (03.00)
Code
RH 03.10.AM
LH 03.10.AN
3-11-3