Rear Bumper Harness-Renew; Tailgate Harness-Renew - Aston Martin V8 Vantage Workshop Manual

Wiring and Circuit Protection (18.01)
Electric Distribution/Electronic Control (18.00)
7. Disconnect multiplug to door mirror.
8. Disconnect multiplug to door latch assembly.
9. Release harness from inner door casing clips (x10).
10. Release harness from outer door casing clips (x8).
11. Release harness grommets from door casing (x2).
12. Remove harness.
Installation
1. Position harness in door and install grommets (x2).
2. Secure harness in door casing clips (x18).
3. Connect multiplug to door latch.
4. Connect multiplug to door mirror
5. Connect multiplug to door speaker.
6. Install plate assembly.
7. Connect multiplugs (x3) and install drivers door control
module.
8. Install drivers door glass regulator (see Workshop
Manual procedure 01.11.DA Regulator - Door Glass -
RH - Renew).

Rear Bumper Harness-Renew

Repair Operation Time (ROT)
Item
Rear Bumper Harness-Renew
Removal
1. Remove rear bumper (see Workshop Manual procedure
01.19.BA Cover Assembly - Rear Bumper - Renew).
2. Disconnect harness multiplugs (x2) in RH wheel arch.
3. Disconnect multiplugs (x2), PDC sensors.
4. Disconnect multiplug from vacuum pump.
5. Disconnect multiplug from shift transfer retro control pdl
rod.
6. Release clips (x8) securing harness to LH wheel arch.
7. Release clip securing harness to evaporative emission
control module bracket.
8. Disconnect multiplug from evaporative emission control
module.
9. Disconnect multiplug from siren control module.
10. Remove bumper harness.
Installation
1. Position bumper harness to body.
2. Secure harness clips (x8) in LH wheel arch.
3. Connect multiplug to evaporative emission control
module.
4. Secure harness clip to evaporative emission control
module bracket.
5. Connect multiplug to siren control module.
6. Connect multiplug to shift transfer retro control pdl rod.
7. Connect multiplug to vacuum pump.
8. Connect harness multiplugs in RH wheel arch.
9. Connect multiplugs (x2), PDC sensors.
18-1-12
10. Install rear bumper (see Workshop Manual procedure
01.19.BA Cover Assembly - Rear Bumper - Renew).

Tailgate Harness-Renew

Repair Operation Time (ROT)
Item
Tailgate Harness-Renew
Removal
1. Battery isolator switch 'OFF'.
2. Remove trim - tailgate lid assembly (see Workshop
Manual procedure 01.05.EF Trim - Tailgate Lid
Assembly - Renew).
3. Disconnect multiplugs (x4), behind trim panel.
4. Disconnect Lucar connectors (x2), heated rear window.
5. Remove rear header panel assembly (see Workshop
Manual procedure 01.05.BK Panel Assembly - Rear
Header - Renew).
6. Disconnect multiplugs (x2), LH and RH side tailgate
harness to main harness.
7. Release harness from clips (x4) LH side.
8. Disconnect blue multiplug behind RH side of rear
header.
Code
9. Release harness from clips (x5), RH side.
18.01.HA
10. Disconnect lucar connectors (x4).
11. Release grommets from body and tailgate (x4).
12. Remove tailgate glass.
13. Release clips (x17) securing harness to tailgate.
14. Manoeuvre and remove harness from tailgate.
Installation
1. Install harness in tailgate.
2. Secure harness clips (x17) in tailgate.
3. Install tailgate glass.
4. Install grommets (x4), body and tailgate.
5. Connect Lucar connectors (x4).
6. Secure harness in clips (x5), RH side.
7. Connect multiplug (blue), RH side.
8. Secure harness with clips (x4), LH side.
9. Connect multiplugs (x2), tailgate harness to main
harness RH and LH sides.
10. Install rear header panel assembly (see Workshop
Manual procedure 01.05.BK Panel Assembly - Rear
Header - Renew).
11. Connect Lucar connectors (x2), heated rear window.
12. Connect multiplugs (x4), tailgate rear.
13. Install trim - tailgate lid (see Workshop Manual
procedure 01.05.EF Trim - Tailgate Lid Assembly -
Renew).
14. Battery isolator switch 'ON'.
Workshop Manual
Code
18.01.JC
October 2005