Specifications; Maintenance; Front Bumper Cover-Renew; Rear Bumper Cover-Renew - Aston Martin V8 Vantage Workshop Manual

Bumpers (01.19)
Body System (01.00)

Specifications

Torque Figures
Description
Front Bumper to bumper bracket
Rear Bumper to Bumper Bracket

Maintenance

Front Bumper Cover-Renew

Repair Operation Time (ROT)
Item
Front Bumper Cover-Renew
Removal
1. Raise vehicle on ramp.
2. Remove front number plate and plinth (see Workshop
Manual procedure 01.19.BD Licence Plate - Plinth
Assembly - Front - Renew).
3. Remove screws (x2) securing front of undertray to
bumper.
4. Remove LH front wheel arch liner (see Workshop
Manual procedure 01.02.FB Wheel Arch Liner - Front -
LH - Renew).
5. Remove RH front wheel arch liner (see Workshop
Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
6. Remove bolts (x6) securing bumper to front wing
7. With assistance release bumper from clips (x2) and
remove bumper.
Installation
1. With assistance position bumper and secure in clips
(x2).
2. Install bolts (x6) bumper to front wing.
3. Install RH front wheel arch liner (see Workshop Manual
procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
4. Install LH front wheel arch liner (see Workshop Manual
procedure 01.02.FB Wheel Arch Liner - Front - LH -
Renew).
5. Install screws (x2) securing front undertray to bumper.
6. Install number plate and plinth (see Workshop Manual
procedure 01.19.BD Licence Plate - Plinth Assembly -
Front - Renew).
7. Lower vehicle on ramp.

Rear Bumper Cover-Renew

Repair Operation Time (ROT)
Item
Rear Bumper Cover-Renew
Removal
1. Raise vehicle on ramp.
2. Remove number plate.
1-12-2
3. Remove LH rear lamp assembly (see Workshop Manual
procedure 17.03.AB Lamp Assembly (Rear) - LH
Renew).
4. Remove RH rear lamp assembly (see Workshop Manual
Nm
procedure 17.03.BB XREF: 280 Lamp Assembly (Rear) -
4-5
RH Renew).
2-3
5. Remove wheel arch liner LH (see Workshop Manual
procedure 01.02.JB Wheel Arch Liner - Rear - RH -
Renew).
6. Remove wheel arch liner RH (see Workshop Manual
procedure 01.02.HB Wheel Arch Liner - Rear - LH -
Renew).
Code
7. Remove tyre mobility kit from the rack.
01.19.AA
8. Remove torx bolts located behind carpets to rear wings
(x2).
9. Remove bolts (x2) in rear light recess.
10. Remove bolts securing bumper to wheel arch (6).
11. Remove bolts (x4) securing bumper to brackets.
12. With assistance Release bumper from body.
13. Release fir trees securing harness to bumper (x6).
14. Release remaining harness to bumper clips (x6)
15. Disconnect multiplugs to parking aid sensors (x2).
16. Disconnect multiplugs to license plate lamps (x2).
17. Remove nuts (x6) securing exhaust finishers to stub
pipes.
18. Remove number plate light assembly (clips x5).
19. Remove parking aid sensors (x2)
20. Remove screw retaining clips (x13)
Installation
1. Install screw retaining clips x13.
2. Install parking aid sensors x2.
3. Install number plate light assembly
4. Install exhaust finishers to stub pipe.
5. With assistance position bumper to body.
6. Connect multiplugs to license plate lamps X2.
7. Connect multiplug to parking aid sensors.
8. Secure harness to bumper (fir trees x6 and clips x6)
9. Install bumper bolts to brackets and body (x10).
10. Install tyre mobility kit to rack.
11. Install number plate.
12. Install RH rear lamp assembly (see Workshop Manual
procedure 17.03.BB Lamp Assembly (Rear) - RH
Renew).
13. Install LH rear lamp assembly (see Workshop Manual
procedure 17.03.AB Lamp Assembly (Rear) - LH
Renew).
14. Install wheel arch liner LH (see Workshop Manual
Code
procedure 01.02.JB Wheel Arch Liner - Rear - RH -
01.19.BA
Renew).
15. Install RH wheel arch liner (see Workshop Manual
procedure 01.02.HB Wheel Arch Liner - Rear - RH -
Renew).
16. Lower vehicle on ramp.
Workshop Manual October 2005