Bulkhead Stud To Starter Cable Assembly-Renew; Bulkhead Stud To Engine Bay Fusebox Cable Assembly-Renew; Bulkhead To Starter Jump Terminal Harness-Renew - Aston Martin V8 Vantage Workshop Manual

Battery System (14.01)
Power Supply (14.00)
7. Remove nuts (x2), battery compartment cover to body.
Remove cover.
8. Remove nut and washer securing battery cable to
battery disconnect switch.
9. Release cable and main battery cable from battery
disconnect switch.
10. Loosen terminal nut, disconnect main battery cable
(positive), remove cable.
Installation
1. Install battery cables (x2), install washer, install and
torque tighten nut.
2. Install battery compartment cover, install and tighten
screws (x2) and nuts (x2).
3. Position rear carpet, install on studs (x2).
4. Connect vehicle battery.
5. Install rear compartment cover.
6. Power drivers seat to original position.
Bulkhead Stud to Starter Cable
Assembly-Renew
Repair Operation Time (ROT)
Item
Bulkhead Stud to Starter Cable
Assembly-Renew
Removal
1. Disconnect vehicle battery.
2. Remove starter motor. (see Workshop Manual
procedure 03.06.AB Starter Motor - Renew).
3. Release rubber cover, remove nut securing battery cable
to bulkhead stud.
4. Release battery cable clip from bracket, remove cable.
Installation
1. Position battery cable to bulkhead stud, install and
torque tighten nut. Install rubber cover.
2. Secure battery cable clip in bracket.
3. Install starter motor (see Workshop Manual procedure
03.06.AB Starter Motor - Renew).
4. Connect vehicle battery.
Bulkhead Stud to Engine Bay Fusebox
Cable Assembly-Renew
Repair Operation Time (ROT)
Item
Bulkhead Stud to Engine Bay Fusebox
Cable Assembly-Renew
Removal
1. Disconnect vehicle battery.
2. Remove engine bay fusebox (see Workshop Manual
procedure 18.01.KD Fuse Box - Engine Bay - Renew).
14-1-6
3. Release rubber cover, remove nut securing cable to
bulkhead stud, Remove cable.
4. Remove rubber cover from cable.
Installation
1. Clean cable connection on bulkhead stud and fusebox.
2. Install rubber cover onto cable.
3. Position cable to bulkhead stud, install and torque
tighten nut.
4. Install engine bay fusebox (see Workshop Manual
procedure 18.01.KD Fuse Box - Engine Bay - Renew).
5. Connect vehicle battery.
Bulkhead to Starter Jump Terminal
Harness-Renew
Repair Operation Time (ROT)
Item
Bulkhead to Starter Jump Terminal
Harness-Renew
Removal
1. Disconnect vehicle battery.
2. Remove terminal jump start (see Workshop Manual
Code
procedure 14.01.EA Terminal - Jump Start - Renew).
14.01.EG
3. Raise vehicle on ramp.
4. Remove RH front wheel arch liner (see Workshop
Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
5. Release battery cable clips (x6), from body.
6. Release battery cable clips (x2) from screen washer
reservoir.
7. Release cover, remove nut securing harness to bulkhead
stud.
8. Release harness from bulkhead stud, manoeuvre and
remove harness.
Installation
1. Position harness to bulkhead stud, install and torque
tighten nut, install cover.
2. Secure harness to body and screen washer reservoir
with clips (x8).
3. Install RH front wheel arch liner (see Workshop Manual
procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
4. Lower vehicle on ramp.
5. Install terminal jump start (see Workshop Manual
Code
procedure 14.01.EA Terminal - Jump Start - Renew).
14.01.EH
6. Connect vehicle battery.
Workshop Manual
Code
14.01.EJ
October 2005