Panasonic FP-E Programming Manual page 1297

5.3 Table of High-level Instructions
The high-level instructions are expressed by the prefixes "F" or "P" with numbers. For most of the high-level
instructions, "F" and "P" types are available. The differences between the two types are explained as follows:
- Instructions with the prefix "F" are executed in every scan while its trigger is in the on.
- Instructions with the prefix "P" are executed only when the leading edge of its trigger is detected.
For the FP0/FP0R/FPΣ/FP-X, the P type high-level instructions are not available.
Num-
Name
ber
Data transfer instructions
F0 16-bit data
P0 move
F1 32-bit data
P1 move
F2 16-bit data
P2 invert and
move
F3 32-bit data
P3 invert and
move
F4 Reading of
P4 head word
No. of the
specified slot
F5 Bit data
P5 move
F6 Hexadecimal
P6 digit (4-bit)
data move
F7 Two 16-bit
P7 data move
F8 Two 32-bit
P8 data move
F10 Block move
P10
F11 Block copy
P11
F12 Data read
from EEP-
ROM
P13 Data write to
EEP-ROM
F12 Data read
from F-ROM
P13 Data write to
F-ROM
F12 Data read
P12 from IC card
F13 Data write to
P13 IC card
F14 Program read
P14 from IC
memory card
: Available, : Not available,
*1) This instruction is available for FP2/FP2SH Ver. 1.5 or later.FP10SH cannot be used
*2) This instruction is available for FP0 Ver. 2.0 or later.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Ope-
Boo-
lean
rand
MV S, D (S)→(D)
PMV
DMV S, D (S+1, S)→(D+1, D)
PDMV
MV S, D
PMV/ (S)→(D)
DMV/ S, D
PDMV/ (S+1, S)→(D+1, D)
GETS S, D The head word No. of the specified slot is
PGETS read.
BTM S, n, The specified one bit in "S" is transferred to
PBTM D the specified one bit in "D". The bit is
specified by "n".
DGT S, n, d The specified one digit in "S" is transferred
PDGT to the specified one digit in "D". The digit is
specified by "n".
MV2 S1, (S1)→(D),
PMV2 S2, D (S2)→(D+1)
DMV2 S1, (S1+1, S1)→(D+1, D),
PDMV2 S2, D (S2+1, S2)→(D+3, D+2)
BKMV S1, The data between "S1" and "S2" is
PBKMV S2, D transferred to the area starting at "D".
COPY S, D1, The data of "S" is transferred to the all area
PCOPY D2 between "D1" and "D2".
ICRD S1, The data stored in the expansion memory
S2, D of the EEP-ROM specified by "S1" and "S2"
are transferred to the area startign at "D".
PICWT S1, The data specified by "S1" and "S2" are
S2, D transferred to the EEP-ROM starting at "D".
ICRD S1, The data stored in the expansion memory
S2, D of the F-ROM specified by "S1" and "S2"
are transferred to the area startign at "D".
PICWT S1, The data specified by "S1" and "S2" are
S2, D transferred to the F-ROM starting at "D".
ICRD S1, The data stored in the expansion memory
PICRD S2, D of the IC card specified by "S1" and "S2"
are transferred to the area startign at "D".
ICWT S1, The data specified by "S1" and "S2" are
PICWT S2, D transferred to the IC card expansion
memory area starting at "D".
PGRD S The program specified using "S" is
PPGRD transferred into the CPU from IC memory
card and executes it.
: Not available partially
Description
5
7
5
7
5
*1
7
7
7
11
7
7
11
*2
11
*2
11
11
11
11
3
5-209
*1