Panasonic FP-E Programming Manual page 1315

Num-
Name
ber
F347 Floating-point
P347 type data
upper and
lower limit
control
F348 Floating-point
P348 type data
dead-band
control
F349 Floating-point
P349 type data
zone control
F350 Floating-point
P350 type data
maxi-mum
value
F351 Floating-point
P351 type data
mini-mum
value
F352 Floating-point
P352 type data total
and mean
values
F353 Floating-point
P353 type data sort
F354 Scaling of
P354 real number
data
: Available, : Not available,
*1) This instruction is available for FP2/FP2SH Ver. 1.5 or later. FP10SH cannot be used.
*2) This instruction is available for FPΣ 32k type.
*3) This instruction is available for FP-X Ver. 1.13 or later.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Ope-
Boolean
rand
FLIMT S1, S2, When (S1+1, S1)>(S3+1, S3),
(S1+1, S1) →(D+1, D)
PFLIMT S3, D
When (S2+1, S2)<(S3+1, S3),
(S2+1, S2) → (D+1, D)
When (S1+1, S1)<or = (S3+1,
S3)<or =(S2+1, S2), (S3+1,
S3)→(D+1, D)
FBAND S1, S2, When (S1+1, S1)>(S3+1, S3),
PFBAND S3, D (S3+1, S3)−(S1+1, S1)→(D+1, D)
When (S2+1, S2)<(S3+1, S3),
(S3+1, S3)−(S2+1, S2)→ (D+1, D)
When (S1+1, S1)<or = (S3+1,
S3)<or =(S2+1, S2), 0.0→(D+1, D)
FZONE S1, S2, When (S3+1, S3)<0.0,
PFZONE S3, D (S3+1, S3)+(S1+1, S1)→(D+1, D)
When (S3+1, S3)=0.0, 0.0→ (D+1,
D)
When (S3+1, S3)>0.0, (S3+1,
S3)+(S2+1, S2) →(D+1, D)
FMAX S1, S2, Searches the maximum value in the
PFMAX D real number data table between the
area selected with "S1" and "S2",
and stores it in the (D+1, D). The
address relative to "S1" is stored in
(D+2).
FMIN S1, S2, Searches the minimum value in the
PFMIN D real number data table between the
area selected with "S1" and "S2",
and stores it in the (D+1, D). The
address relative to "S1" is stored in
(D+2).
FMEAN S1, S2, The total value and the mean value
PFMEAN D of the real number data from the
area selected with "S1" to "S2" are
obtained. The total value is stored in
the (D+1, D) and the mean value is
stored in the (D+3, D+2).
FSORT S1, S2, The real number data from the area
PFSORT S3 speciified by "S1" to "S2" are stored
in ascending order (the smallest
word is first) or descending order
(the largest word is first).
FSCAL S1, S2, Scaling (linearization) on a real
PFSCAL D number data table is performed, and
the output (Y) to an input value (X)
is calculated.
: Not available partially
Description
17
17
17
12
8
8
8
8
*2 *3 *1
5-227
*1