Flex Mux Configuration Commands (Flex Mux Pcb Installed Only - Comtech EF Data SDM-300A Installation And Operation Manual

SDM-300A Satellite Modem
B.6 Flex Mux Configuration Commands (Flex Mux PCB Installed
Only)
TX Channel Command:
#1 Enable Response:
Status:
Response:
TX Channel Command:
#2 Enable Response:
Status:
Response:
TX Channel Command:
#3 Enable Response:
Status:
Response:
TX Channel Command:
#3 Data Response:
Rate
Status:
Response:
TX Channel Command:
#4 Enable Response:
Status:
Response:
TX Channel Command:
#4 Data Response:
Rate
Status:
Response:
TX Channel Command:
Clock Response:
Phase
(Channels Status:
#3 and #4) Response:
TX Channel Command:
Data Phase Response:
(Channels
#3 and #4) Status:
Response:
Rev. 4
<add/TCEN_1_xxx'cr'
>add/TCEN_1_xxx'cr''lf']
<add/TCEN_1'cr'
>add/TCEN_1_xxx'cr''lf']
<add/TCEN_2_xxx'cr'
>add/TCEN_2_xxx'cr''lf']
<add/TCEN_2'cr'
>add/TCEN_2_xxx'cr''lf']
<add/TCEN_3_xxxxxxxxxxx'cr'
>add/TCEN_3_xxxxxxxxxxx'cr''lf']
<add/TCEN_3'cr'
>add/TCEN_3_xxxxxxxxxxx'cr''lf']
<add/TCDR_3_xxxxxx'cr'
>add/TCDR_3_xxxxxx'cr''lf']
<add/TCDR_3'cr'
>add/TCDR_3_xxxxxx'cr''lf']
<add/TCEN_4_xxxxxxxxxxx'cr'
>add/TCEN_4_xxxxxxxxxxx'cr''lf']
<add/TCEN_4'cr'
>add/TCEN_4_xxxxxxxxxxx'cr''lf']
<add/TCDR_4_xxxxxx'cr'
>add/TCDR_4_xxxxxx'cr''lf']
<add/TCDR_4'cr'
>add/TCDR_4_xxxxxx'cr''lf']
<add/TCCP_x_yyy'cr'
>add/TCCP_x_yyy'cr''lf']
<add/TCCP_x'cr'
>add/TCCP_x_yyy'cr''lf']
<add/TCDP_x_yyy'cr'
>add/TCDP_x_yyy'cr''lf']
<add/TCDP_x'cr'
>add/TCDP_x_yyy'cr''lf']
Where: xxx = OFF (D&I Disabled), ON (D&I Enabled).
This command enables channel #1 for D&I operation, or can
be disabled.
Where: xxx = OFF (ADPCM Disabled), ON (ADPCM Enabled).
This command enables channel #2 for ADPCM operation, or
can be disabled.
Where: xxxxxxxxxxx = OFF (Channel Disabled), AUPC
(Channel Enabled for AUPC), ASYNC_RS232 (Channel
Enabled for ASYNC RS232), SYNC_RS232 (Channel Enabled
for SYNC RS232), ASYNC_RS422 (Channel Enabled for
ASYNC RS422), SYNC_RS422 (Channel Enabled for SYNC
RS422).
This command enables channel #3 for SYNC/ASYNC
RS232/RS422 operation, AUPC operation, or can be disabled.
Where: xxxxxx = 0.6 to 4000.0 for RS422 (kbit/s in 100 bit/s
steps), 0.6 to 64.0 for RS232 kbit/s in 100 kbit/s steps).
Where: xxxxxxxxxxx = OFF (Channel Disabled), AUPC
(Channel Enabled for AUPC), ASYNC_RS232 (Channel
Enabled for ASYNC RS232), SYNC_RS232 (Channel Enabled
for SYNC RS232), ASYNC_RS485 (Channel Enabled for
ASYNC RS485).
This command enables channel #4 for SYNC/ASYNC RS232
operation, ASYNC RS485 operation, AUPC operation, or can
be disabled.
Where: xxxxxx = 0.6 to 64.0 for RS232 (kbit/s in 100 bit/s
steps).
Where:
x = 3 or 4 (channel number).
yyy = NRM (normal clock phasing), INV (inverted clock
phasing.
Where:
x = 3 or 4 (channel number).
yyy = NRM (normal data phasing), INV (inverted data
phasing.
Remote Control Operation
B–53