System Configuration Commands - Comtech EF Data SDM-300A Installation And Operation Manual

Remote Control Operation
B.3.4

System Configuration Commands

Time Of Command:
Day Response:
Status:
Response:
Date Command:
Response:
Status:
Response:
Remote Command:
Response:
Clear Command:
Stored Response:
Faults
Modem Command:
Operation Response:
Mode
Status:
Response:
System Command:
Modem Response:
Type
Status:
Response:
Save Command:
Modem Response:
Config.
Recall Command:
Modem Response:
Config.
Local Command:
Modem Response:
AUPC
Mode Status:
Response:
B–14
<add/TIME_hh:mmxx'cr'
>add/TIME_hh:mmxx'cr''lf']
<add/TIME_'cr'
>add/TIME_hh:mmxx'cr''lf']
<add/DATE_mm/dd/yyyy'cr'
>add/DATE_mm/dd/yyyy'cr''lf']
<add/DATE_'cr'
>add/DATE_mm/dd/yyyy'cr''lf']
<add/REM_'cr'
>add/REM_'cr''lf']
<add/CLSF_'cr'
>add/CLSF_'cr''lf']
<add/MOM_xxxxxxx'cr'
>add/MOM_xxxxxxx'cr''lf']
<add/MOM_'cr'
>add/MOM_xxxxxxx'cr''lf']
<add/SMT_xxxxxxx'cr'
>add/SMT_xxxxxxx'cr''lf']
<add/SMT_'cr'
>add/SMT_xxxxxxx'cr''lf']
<add/SMC_n'cr'
>add/SMC_n'cr''lf']
<add/RMC_n'cr'
>add/RMC_n'cr''lf']
<add/LMA_xxx'cr'
>add/LMA_xxx'cr''lf']
<add/LMA_'cr'
>add/LMA_xxx'cr''lf']
SDM-300A Satellite Modem
Where:
hh = 1 to 12 (hours).
mm = 00 to 59 (minutes).
xx = AM or PM.
Where:
mm = 1 to 12 (month).
dd = 1 to 31 (day).
yyyy = 00 to 99 (year) in 2 - digit year mode, and 1975
to 1999 and 2000 to 2075 in 4 - digit mode.
Configures the modem for remote operation.
The SDM300A will respond to any status request at any
time. However, the SDM300A must be in 'Remote Mode'
to change configuration parameters.
This command is used to clear all stored faults logged by
the SDM300A.
Where: xxxxxxx = TX_ONLY, RX_ONLY, or DUPLEX.
This command configures the modem for simplex or
duplex operation modes. When transmit only mode is
selected, receive faults are inhibited and when receive
only mode is selected, transmit faults are inhibited.
Where: xxxxxx = IDR, IBS, DI, ASYNC, EFD, or
CUSTOM.
Where: n = 1, 2, 3, 4, or 5 (stored configuration number).
This command saves the current modem configuration for
recall at a later time using the 'RMC_' command. Up to
five different modem configurations can be saved.
Where: n = 1, 2, 3, 4, or 5 (stored configuration number).
This command causes the modem to be reprogrammed
with configuration parameters previously saved using the
'SMC_' command. One of five saved configurations can
be specified.
Where: xxx = ON or OFF.
This command configures the modem for the LOCAL
MODEM AUPC mode. When 'ON' is selected, the AUPC
configuration can be entered.
Rev. 4