Comtech EF Data SDM-300A Installation And Operation Manual page 291

Remote Control Operation
AUPC Command:
Eb/N0 Response:
Target Set
Point Status:
Response:
AUPC Command:
Maximum Response:
Tracking
Rate Status:
Response:
AUPC Local Command:
Carrier Loss Response:
Action
Status:
Response:
AUPC Command:
Remote Response:
Carrier Loss
Action Status:
Response:
Remote
Modem
AUPC
Commands
Remote Command:
AUPC Response:
Enable
Remote Command:
Interface Response:
Substitution
Pattern Status:
Response:
Remote Command:
Interface Response:
Baseband
Loopback Status:
Response:
Remote Command:
Interface Response:
Read Error
Status Example:
Command:
Response:
B–16
<add/ENSP_nn.n'cr'
>add/ENSP_nn.n'cr''lf']
<add/ENSP_'cr'
>add/ENSP_nn.n'cr''lf']
<add/MAXT_n.n'cr'
>add/MAXT_n.n'cr''lf']
<add/MAXT_'cr'
>add/MAXT_n.n'cr''lf']
<add/LCL_xxxx'cr'
>add/LCL_xxxx'cr''lf']
<add/LCL_'cr'
>add/LCL_xxxx'cr''lf']
<add/RCL_xxxx'cr'
>add/RCL_xxxx'cr''lf']
<add/RCL_'cr'
>add/RCL_xxxx'cr''lf']
<add/RPC_xxx'cr'
>add/RPC_xxx'cr''lf']
<add/RISP_xxx'cr'
>add/RISP_xxx'cr''lf']
<add/RISP_'cr'
>add/RISP_xxx'cr''lf']
<add/RBBL_xxx'cr'
>add/RBBL_xxx'cr''lf']
<add/RBBL_'cr'
>add/RBBL_xxx'cr''lf']
<add/RRES_'cr'
>add/RRES_nE-e'cr''lf']
<add/RRES_'cr'
>add/RRES_2E-6'cr''lf']
SDM-300A Satellite Modem
Where: nn.n = 3.2 to 16.0, in 0.1 increments (Eb/N0 in
dB).
Note: ASYNC Overhead only.
Where: n.n = 0.5 to 6.0, in 0.5 increments (max tracking
rate in dBm/minute).
Note: ASYNC Overhead only.
Where: xxxx = HOLD, NOM, or MAX (power level setting
when local carrier loss).
Note: ASYNC Overhead only.
Where: xxxx = HOLD, NOM, or MAX (power level setting
when remote carrier loss).
Note: ASYNC Overhead only.
Notes:
1. Always wait 3 seconds between consecutive
remote modem command/status polls.
2. If Local AUPC is not enabled, status commands
will return last known condition. They will also
request status from the remote modem. This
allows a second request to return proper status.
Where: xxx = ON or OFF (remote AUPC enable).
Note: ASYNC Overhead only.
Where: xxx = ON or OFF (remote transmit 2047 pattern
enable).
Note: Transmit 2047 Pattern.
Where: xxx = ON or OFF (remote baseband loopback
enable).
Note: ASYNC Overhead only.
Where:
n = 1 to 9 (error rate number).
e = 2 to 6 (exponent).
Note: Received 2047 Pattern.
This command returns 2047 BER from the remote AUPC
modem. If data is not valid, the message 'No_Data' is
returned in lieu of BER data.
Rev. 4