Interface Configuration Commands - Comtech EF Data SDM-300A Installation And Operation Manual

Remote Control Operation
B.3.3

Interface Configuration Commands

Interface Command:
Transmit Response:
Overhead
Type Status:
Response:
Interface Command:
Receive Response:
Overhead
Type Status:
Response:
TX Driver Command:
Type Response:
Status:
Response:
RX Driver Command:
Type Response:
Status:
Response:
Transmit Command:
Clock Response:
Status:
Response:
External Command:
Clock- Response:
Reference
Frequency Status:
Response:
Transmit Command:
Clock Response:
Phase
Status:
Response:
Buffer Clock Command:
Response:
Status:
Response:
Receive Command:
Clock Response:
Phase
Status:
Response:
Baseband Command:
Loopback Response:
Status:
Response:
B–8
<add/ITOT_xxxxx'cr'
>add/ITOT_xxxxx'cr''lf']
<add/ITOT_'cr'
>add/ITOT_xxxxx'cr''lf']
<add/IROT_xxxxx'cr'
>add/IROT_xxxxx'cr''lf']
<add/IROT_'cr'
>add/IROT_xxxxx'cr''lf']
<add/TXDR_xxxxx'cr'
>add/TXDR_xxxxx'cr''lf']
<add/TXDR_'cr'
>add/TXDR_xxxxx'cr''lf']
<add/RXDR_xxxxx'cr'
>add/RXDR_xxxxx'cr''lf']
<add/RXDR_'cr'
>add/RXDR_xxxxx'cr''lf']
<add/TC_xxx'cr'
>add/TC_xxx'cr''lf']
<add/TC_'cr'
>add/TC_xxx'cr''lf']
<add/ERF_nnnnn.n'cr'
>add/ERF_nnnnn.n'cr''lf']
<add/ERF_'cr'
>add/ERF_nnnnn.n'cr''lf']
<add/TCP_xxxx'cr'
>add/TCP_xxxx'cr''lf']
<add/TCP_'cr'
>add/TCP_xxxx'cr''lf']
<add/BC_xxx'cr'
>add/BC_xxx'cr''lf']
<add/BC_'cr'
>add/BC_xxx'cr''lf']
<add/RCP_xxx'cr'
>add/RCP_xxx'cr''lf']
<add/RCP_'cr'
>add/RCP_xxx'cr''lf']
<add/BBL_xxx'cr'
>add/BBL_xxx'cr''lf']
<add/BBL_'cr'
>add/BBL_xxx'cr''lf']
SDM-300A Satellite Modem
Where: xxxxx = NONE, IDR, IBS, DI, ASYNC, or FLEX.
Where: xxxxx = NONE, IDR, IBS, DI, ASYNC, or FLEX.
Where: xxxxx = G703, V35, RS422, or RS232.
Where: xxxxx = G703, V35, RS422, or RS232.
Where: xxx = INT (internal SCT clock), EXT (external TX
terrestrial clock), REF (external clock-reference
frequency).
Where: nnnnn.n = 8.0 to 10000.0 (external clock
frequency in kHz).
Where: xxxx = NRM (normal clock phasing), INV (inverted
clock phasing), AUTO (automatic clock phasing).
Where: xxx = INT (internal SCT clock), EXT (external TX
terrestrial clock), SAT (receive satellite clock), REF
(external clock-reference frequency), INS (insert clock).
Where: xxx = NRM (normal clock phasing), INV (inverted
clock phasing).
Where: xxx = ON or OFF.
Rev. 4