Table of Contents
Advertisement
MAINTENANCE MANUAL > Troubleshooting > Details on Errors and Malfunctions > List of Error Messages
Model SWJ-320S Issued 2012.07.19 Revised 2013.03.08 F/W ver
7.1.2 List of Error Messages
List of Error Messages ?1/5?
No.
LCD
ERROR 108
HD
1
CONNECT[12345678]
ERROR 108
HD THERMIS[12345678]
2
ERROR 128
HDC FIFO OVER
3
ERROR 128
HDC FIFO UNDER
4
ERROR 129
BATTERY EXCHANGE
5
ERROR 12a
HDC SPEED
6
ERROR 12e
HeadFaild /HDC[12__]
7
ERROR 130
HD DATA SEQ
8
© 2013 MIMAKI ENGINEERING CO.,LTD.
Cause
Head connection error
(Head connection can not be confirmed)
Head thermistor
(Head temperature can not be measured)
HDC FIFO OVER error
(Data transmission speed is too fast Con-
trol PCB trouble)
HDC FIFO OVERRUN is detected at the
scan slider process (ScanSlider)
HDC FIFO UNDER error
(Data transmission speed is too slow Con-
trol PCB trouble)
HDC FIFO UNDERRUN is detected at the
scan slider process (ScanSlider)
Battery dead (RTC battery dead is
detected.)
Proper information of Printer or Time
(Dedicated IC) unusable on Printer initial-
izing process (opinit).
Ink discharging trigger error
As intervals of ink discharging trigger are
too short, next discharging trigger occurs
before one wave shape is completed.
Printer head which is connected the HDC
PCB that displayed number on the LCD is
out of order.
Head data transferring sequence error
Remark
1.0
List of Countermeasures
1. Check the setting of loading number of the head in the
parameter.
(System parameter No.41 HEAD NO=3)
2. Check connection between the HDC PCB from the Print
Head
3. Replace the HDC PCB with a new one.
4. Replace the Print Head with a new one.
1. Check the parameter.
(Is the scan parameter the default value?)
2. Update F/W.
3. Check if there is no data error from RIP.
4. To make sure, repeat RIP.
5. Disconnect and connect the FFC located between the MAIN
PCB and the HDC PCB.
6. Replace the FFC and cable located between the MAIN PCB
and the HDC PCB.
7. Replace the HDC PCB with a new one.
8. Replace the MAIN PCB with a new one.
1. Replace a battery equipped on the MAIN PCB with new one.
(CR2032)
*The new battery should be the same product or the
equivalent.
*Discard the old battery according to the instruction
from the maker.
1. Perform the linear encoder test.
2. Replace the linear scale.
3. Replace the linear encoder sensor.
4. Replace the HDC PCB with a new
5. Replace the MAIN PCB with a new
1. Replace the cable between the HDC PCB from the Print
Head with a new one.
2. Replace the Print Head with a new one.
3. Replace the HDC PCB with a new
1. Disconnect and connect the FFC located between the HDC
PCB and the MAIN PCB.
2. Replace the FFC located between the HDC PCB and the
MAIN PCB.
3. Replace the HDC PCB with a new one.
4. Replace the MAIN PCB with a new one.
Rev.
1.2
1
(Refer to 6.4.7)
(Refer to 3.3.1)
2
3
(Refer to 6.4.7)
(Refer to 3.3.1)
4
one.(Refer to 6.4.7)
5
one.(Refer to 3.3.1)
(Refer to 3.3.1)
6
one.(Refer to 6.4.7)
(Refer to 6.4.7)
7
(Refer to 3.3.1)
8
7.1.2
R.1.2
P.1
Advertisement
Table of Contents
