Error Code Table - Canon iR7086 Series Service Manual

16.1 Error Code Table

16.1.1 Error Code Table
iR7105 / iR7095 / iR7086
Code Description
*: model equipped with DADF-Q1 (outside Japan, iR7105/7095; inside Japan: iR7105/7095/7086).
**: model equipped with DADF-M1 (outside Japan: iR7086).
E000 The fixing unit has overheated.
After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
E001 The fixing unit has overheated.
After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
E002 The fixing unit has overheated.
After correcting the error, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
E003 The fixing unit temperature is abnormally low.
After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
E004 The fixing unit has a fault. (protective circuit ON)
After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
E005 The fixing web has run out.
After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
E010 The main motor rotation is faulty.
E012 The drum motor rotation is faulty.
E013 The waste toner feedscrew is stuck. (clogged with waste toner)
After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
E014 The fixing motor rotation is faulty.
E015 The pickup motor rotation is faulty.
E019 The waste toner case is full.
E020 The developing assembly is out of toner. The buffer motor rotation is faulty. The toner feed
motor (sub hopper) rotation is faulty.
After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
E025 The toner bottle motor rotation is faulty.
E032 The copy data controller/NE controller counter fails to operate.
E043 The rotation of the pickup motor of the side paper deck is faulty.
E051 The horizontal registration HP detection has an error.
E065 The high-voltage output has a fault. (primary charging assembly)
E067 The high-voltage output has a fault.
E068 The high-voltage output has a fault. (separation charging assembly)
E069 The transfer high voltage has an error.
E102 A read error has occurred in relation to the laser scanner unit EEPROM data.
E110 The laser scanner motor rotation has a fault.
E111 The laser scanner motor cooling fan rotation has a fault.
E121 A fault exists in the rotation of the following: laser scanner unit cooling fan, reader heat
discharge fan 1, reader heat discharge fan 2.
E193 Video PCB initialization error
E197 The laser scanner motor communication has a fault.
E202 The scanner HP detection mechanism has a fault.
E225 The intensity of the scanning lamp is inadequate. (The lamp is exhausted.)
E227 The reader unit power supply (24 V) has a fault.
E240 ** A fault exists in the communication between the main controller and the DC controller.
E248 A fault exists in the following: main controller SRAM, reader controller EEPROM.
E251 The inverter cooling fan rotation is faulty.
E302 Shading operation is faulty.
E315 The image data codec has a fault.
E351 An error has occurred in the main controller communication.
E400 ** An ADF communication error has occurred.
E402 * The ADF belt motor rotation is faulty.
E404 * The ADF delivery motor rotation is faulty.
E405 * The ADF separation motor rotation is faulty.
E410 * The ADF pickup motor rotation is faulty.
E413 ** The ADF shift motor rotation is faulty.
E420 * An ADF EEPROM read error has occurred.
E490 The ADF is of the wrong type.
E500 An Finisher communication error has occurred.
E602 The HDD has an error.
E604 The time memory (DDR-SDRAM) is faulty or inadequate.
T-16-1
Chapter 16
0011-6724
16-1