Canon iR7086 Series Service Manual page 647

*: model equipped with DADF-Q1 (outside Japan: iR7105/7095; inside Japan: All model).
**: model equipped with DADF-M1 (outside Japan: iR7086).
***: up graded version
Sub item
CONFIG Select several system software stored in the hard disk, change the nation/area, paper size.
<Procedure>
1) Select <CONFIG>.
2) Select the item to change.
3) Press the +/- key. (Each press changes the setting.)
4) Display the contents to be needed, press OK key.
5) Turn off and then back on the main power switch.
XXYYZZAA
XX: country (e.g., JP=Japan)
YY (*): language (e.g., ja=Japanese)
ZZ: (*) destination (e.g., 00=Canon)
AA: paper size series (00=AB; 01=inch; 02=A; 03=inch/AB)
*: Cannot change the setting.
TR-SP-C1 Use it to change the transfer/separation output settings for pickup from the right deck.
settings
MEMO:
0: plain paper (default); 1: recycled paper; 2: tracing paper; 3: Thick paper
- In the case that the setting value is 0, control as for the paper that was set at the user mode or manual feeding.
- In the case that the setting value is 1~3, control as for the recycled paper/tracing paper/thick paper. However, only in the case of
the setting of tracing paper/tab paper at the user mode or manual feeding, the setting of the user mode and manual feeding is
prioritized over this service mode setting.
TR-SP-C2 Use it to change the transfer/separation output setting for pickup from the left deck.
settings
0: plain paper (defeat); 1: recycled paper; 2: tracing paper; 3: For thick paper
MEMO:
- In the case that the setting value is 0, control as for the paper that was set at the user mode or manual feeding.
- In the case that the setting value is 1~3, control as for the recycled paper/tracing paper/thick paper. However, only in the case of
the setting of tracing paper/tab paper at the user mode or manual feeding, the setting of the user mode and manual feeding is
prioritized over this service mode setting.
TR-SP-C3 Use it to change the transfer/separation output setting for cassette 3.
settings
0: plain paper (default); 1: recycled paper; 2: tracing paper; 3: For thick paper
MEMO:
- In the case that the setting value is 0, control as for the paper that was set at the user mode or manual feeding.
- In the case that the setting value is 1~3, control as for the recycled paper/tracing paper/thick paper. However, only in the case of
the setting of tracing paper/tab paper at the user mode or manual feeding, the setting of the user mode and manual feeding is
prioritized over this service mode setting.
TR-SP-C4 Use it to change the transfer/separation output setting for pickup from cassette 4.
settings
0: plain paper (default); 1: recycled paper; 2: tracing paper; 3: For thick paper
MEMO:
- In the case that the setting value is 0, control as for the paper that was set at the user mode or manual feeding.
- In the case that the setting value is 1~3, control as for the recycled paper/tracing paper/thick paper. However, only in the case of
the setting of tracing paper/tab paper at the user mode or manual feeding, the setting of the user mode and manual feeding is
prioritized over this service mode setting.
TR-SP-MF Use it to change the transfer/separation output setting for pickup from the manual feeder tray.
settings
0: plain paper (default); 1: recycled paper; 2: tracing paper; 3: For thick paper
MEMO:
- In the case that the setting value is 0, control as for the paper that was set at the user mode or manual feeding.
- In the case that the setting value is 1~3, control as for the recycled paper/tracing paper/thick paper. However, only in the case of
the setting of tracing paper/tab paper at the user mode or manual feeding, the setting of the user mode and manual feeding is
prioritized over this service mode setting.
TR-SP-DK Use it to change the transfer/separation output setting for pickup from the side paper deck.
settings
0: plain paper (default); 1: recycled paper; 2; tracing paper; 3: For thick paper
MEMO:
- In the case that the setting value is 0, control as for the paper that was set at the user mode or manual feeding.
- In the case that the setting value is 1~3, control as for the recycled paper/tracing paper/thick paper. However, only in the case of
the setting of tracing paper/tab paper at the user mode or manual feeding, the setting of the user mode and manual feeding is
prioritized over this service mode setting.
COPIER > OPTION > BODY
Description
Chapter 17
Level
1
1
1
1
1
1
1
17-59