Canon iR7086 Series Service Manual page 663

*: model equipped with DADF-Q1 (outside Japan: iR7105/7095; inside Japan: All model).
**: model equipped with DADF-M1 (outside Japan: iR7086).
***: up graded version
Sub item
ATCT-ADD Auto clear time additional SW
***
This function is to set the auto clear time(or auto-offline transfer time that correspounds with auto clear time) to less than 1 min.
Auto clear time additional SW
This function allows to set the auto clear time to 10sec, 20sec, 30sec, 40sec, 50sec.
(Conventionally, 1 to 9 min)
This function is to set the auto clear time(or auto-offline transfer time that correspounds with auto clear time) to less than 1 min.
Setting range
0: Without addition
1: With addition (10sec, 20sec, 30sec, 40sec, 50sec additions)
Remarks
When this SW is activated, there is no message of [Numeric key is also available for entering (0min=none/1 to 9 min)] at the auto clear
setting screen in user mode.
HDCR-DSW Selection of whether to display 'all HDD data clear ON/OFF' item in user mode
***
To select whether to display the 'all HDD data clear ON/OFF' item in the user mode.
This mode takes effect only when the all HDD data clear function (licensed) is activated.
When the user asks for the item to be provided.
0: The item is not displayed.[default]
1: The item is displayed.
PB-MAX-N Not for use
***
PB-MAX-T Not for use
***
SIZE-DET Use it to enable/disable the original size detection function.
The machine is designed so that the scanning lamp goes on for detection of the size of the original when the copyboard cover is opened
and then closed; if the user finds its light to be too intense, set it to '0'.
settings
0: off; 1: on (default)
DATE-DSP Use it to switch between date notations.
settings
0: YYMM/DD; 1: DD/MM/YY; 2: MM/DD/YY
MB-CCV Use it to set restrictions on the individuals permitted the use of mail box control card.
settings
0: do not restrict (default); 1: restrict
PR-D-SEL Use it to set the density for printing (PDL input).
settings
0: (light) <->4 (standard; default) <-> 8 (dark)
TRY-STP Use it to set the output interrupt mode used in response to a tray full condition.
settings
0: normal mode (suspend when finisher tray becomes full; default); 1: suspend in relation to height
MF-LG-ST Use it to set extra length mode key.
settings
0: normal (default); 1: indicate extra length key on supported mode screen
SPECK-DP Use it to enable/disable display of a warning message in response to the result of dust detection for stream reading.
settings
0: do not indicate; 1: indicate (default)
CNT-DISP Use it to enable/disable the indication of a serial number in response to a press on the counter check mode.
settings
0: indicate (default); 1: do not indicate
PH-D-SEL Use it to specify the number of lines for photo mode copy.
settings
0: 141 lines (default); 1: 134 lines
If setting '1', the degree of half-tone unevenness decreases despite of lower resolution.
MEMO:
-Effective only at copying (ineffective at printing)
-This item is not used at normal servicing.
OP-SZ-DT Use it to enable/disable the original size detection function in reference to the opening of the copyboard cover.
The machine may be set so that it detects the size of an original with the copyboard cover open (e.g., for a book).
settings
0: off (default); 1: on
If set to '1', the machine executes original size detection in response to a press on the Start key.
NW-SCAN Use it to enable/disable the network scan function.
settings
0: do not permit; 1: permit
This choice is not available on a Japanese model. For a non-Japanese PS/PCL model, the settings is fixed to '1'.
COPIER > OPTION > USER
Description
Chapter 17
Level
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
17-75