Canon iR7086 Series Service Manual page 661

*: model equipped with DADF-Q1 (outside Japan: iR7105/7095; inside Japan: All model).
**: model equipped with DADF-M1 (outside Japan: iR7086).
***: up graded version
Sub item
MEAP-PRI Changing the task priority of MEAP
***
The task priority of MEAP increased when this mode is on.
0: OFF
1: ON
Default: 1
Use this mode when increasing the MEAP performance.
- Enable to logout even during the process of PDL job.
- Display the VxWorks task list from the Console menu, and check the task priority of JVM.
PDLEVCT1 PDL continuous job event decimation
***
To increase the speed of the PDL continuous jobs, install a decimation function for the events to be sent to PDL-PIPIT on the CPCA.
The UI display has some mismatch regarding event processing, therefore it shall be allowed for the service technician to turn off the
Event Decimation function with Service Switch.
This item displays the CPCA event to be decimated and the Status.
Setting range
0: No event decimation
1: Decimates job status change/job list change.
Status of interaction/executing/complete are excluded.
2: Decimates job status change/job list change.
Status of interaction is excluded.
[Value of factory shipping/default: 0]
Use when there occurs a complaint of the UI display.
<USER>
*: model equipped with DADF-Q1 (outside Japan: iR7105/7095; inside Japan: All model).
**: model equipped with DADF-M1 (outside Japan: iR7086).
***: up graded version
Sub item
COPY-LIM Use it to change the upper limit for the number of copies.
settings
1 to 9999 prints (default: 9999)
SLEEP Use it to enable/disable the sleep function.
settings
0: off; 1: on (default)
The sleep function depends on the timer set in user mode.
WEB-DISP Use it to enable/disable the indication of a fixing web length warning message.
settings
0: off (do not indicate warning; default); 1: on (indicate warning)
If set to '0', the message will be limited to the service mode screen.
W-TONER Use it to turn off/on the waste toner case full message.
settings
0: off (do not indicate message; default); 1: on (indicate message)
If set to '0', the warning message will be limited to the service mode screen.
COUNTER1 Use it to set soft counter 1 for the counter status verification screen.
settings
101: total 1 (fixed)
COUNTER2 Use it to set soft counters 2 through 6 for the counter status verification screen.
to
settings
COUNTER6
0 to 999
For a list of settings, see the "Soft Counter Specifications" found later.
CONTROL enables/disables the charging mechanism (PDL job)
When connecting with the account-managing device (e.g., coin vendor, non-Canon control card), it switches over the count pulse (on/
off) in the account-managing device.
settings
0: do not restrict (default); 1: restrict
When charging against PDL prints, set '1'.
B4-L-CNT For soft counters 1 through 6, use it to specify whether B4 should be counted as large-size or small-size.
settings
0: small size (default); 1: large size
COPY-JOB Use it to prohibit reservation of a copy job when a card reader/coin vender is in use.
settings
0: enable reservation (default); 1: disable reservation
TAB-ROT Use it to enable/disable rotation of images by 180 deg for PDL printing (if tab paper is used for landscape orientation).
settings
0: do not rotate (default); 1: rotate
COPIER > OPTION > BODY
Description
COPIER > OPTION > USER
Description
Chapter 17
Level
2
2
Level
1
1
1
1
1
1
1
1
1
1
17-73