Points To Note At Time Of Downloading; Installing The System Software (System Cd -> Sst) - Canon iR7086 Series Service Manual

Installing the System Software
When downloaded, the system software is stored in the temporary storage area of the HDD. At the end of downloading, the main power switch must be turned off
and then back on, thus restarting the machine and writing the system software to both system area and flash ROM from the temporary storage area. When the main
power switch is turned off and then back on once again, the machine will start up using the new system software.

18.1.3 Points to Note at Time of Downloading

iR7105 / iR7095 / iR7086
Do Not Turn Off the Power During Download/Write Operation
Do not turn off the power while the system software is being downloaded/written. Otherwise, the machine may fail to start up when its power is turned back on. (If
such is the case, execute HDD formatting, and download the system software. In the case of a boot ROM, replace the DIMM-ROM.)
Points to Note About Upgrading the DC Controller/Reader Controller
The DC controller/reader controller may be downloaded in either in normal mode or in safe mode. If done in safe mode, however, the controller version information
cannot be obtained, causing the data retained by the SST to be written over. It is a good idea, therefore, to use normal mode (so that the software will not be replaced
with software of a previous version).
18.2 Making Preparations
18.2.1 Installing the System Software (System CD -> SST)
iR7105 / iR7095 / iR7086
Here, you will be copying the system software found on the System CD to the SST.
[Preparatory Work]
Requirements
- PC to which the SST (version 3.21 or later) has been installed
- System CD
[Installing the System Software]
1) Turn on the PC.
2) Set the System CD in the PC.
3) Start up the SST.
4) Click [Register Firmware].
Status of reception
(sample)
- - - Download Mode - - - - - - Do wnload Mode - - -
[ iR2270i-JPjaxxxx-MN.dsh ] - - - - xx% [ iR2270i-JPjaxxxx-MN.dsh ] - - - - xx%
System
Software
2 )
The main power switch is turned off and then on.
Writing takes place.
3 )
<<<<< do <<<<< download shell >>>>> wnload shell >>>>>
[ SYSTEM JPja-m ] - - - - [ SYSTEM JPja-m ] - - - - Upgrading complete Upg ading complete
[ SYSTEM ZZ ] - - - - - - - [ SYSTEM ZZ ] - - - - - - - Upgrading complete Upg ading complete
Temporary
[ SYSTEM JPja-w ] - - - - [ SYSTEM JPja-w ] - - - - Upg Upgrading complete ading complete
[ SYSTEM ZZ ] - - - - - - - [ SYSTEM ZZ ] - - - - - - - Upg Upgrading complete ading complete
storage area
[ FONT F ] - - - - - - - - - - [ FONT F ] - - - - - - - - - - Upg Upgrading complete ading complete
[ FONT G ] - - - - - - - - - - [ FONT G ] - - - - - - - - - - Upg Upgrading complete ading complete
+++ Switch OFF the po +++ Switch OFF the power then ON. er then ON. +++ +++
System area
Boot
FLASH
1 )
The system software is downloaded.
HDD
System
Software
ROM
4 )
The main motor switch
is turned off and then on.
ROM
5 )
The machine starts up using
the new version.
F-18-3
- - - Download Mode - - - - - - Do wnload Mode - - -
[ iR2270i-JPjaxxxx-MN.dsh ] - - - - - - - - - - [ iR2270i-JPjaxxxx-MN.dsh ] - - - - - - - - - - Complete Complete
[ iR2270iM-JPjaxxxx-1F77-MN.PRG ] - - - - [ iR2270iM-JPjaxxxx-1F77-MN.PRG ] - - - -
Complete Complete
[ iR2270iM-ZZjaxxxx-49AD.PRG ] - - - - - - - [ iR2270iM-ZZjaxxxx-49AD .PRG ] - - - - - - - Complete Complete
[ iR2270iW-JPjaxxxx-5C16-MN.PRG ] - - - - [ iR2270iW -JPjaxxxx-5C16-MN.PRG ] - - - - Complete Complete
[ iR2270iW-ZZjaxxxx-A825.PRG ] - - - - - - - [ iR2270iW -ZZjaxxxx-A825.PRG ] - - - - - - - Complete Complete
[ iR2270iF-JPjaxxxx-DE96-ICC.PRG ] - - - - [ iR2270iF-JPjaxxxx-DE96-ICC .PRG ] - - - - Complete Complete
[ iR2270iW [ iR2270iW-ZZjaxxxx-A825.PRG ] - - - - - - - -ZZjaxxxx-A825.PRG ] - - - - - - - Complete Complete
[ iR2270iG-JPjaxxxx-EC30-ICC.PRG ] - - - - [ iR2270iG-JPjaxxxx-EC30-ICC .PRG ] - - - -
Complete Complete
HDD
System
Software
Temporary
storage area
Chapter 18
0011-6811
0011-6751
18-5