Canon iR7086 Series Service Manual page 666

Chapter 17
*: model equipped with DADF-Q1 (outside Japan: iR7105/7095; inside Japan: All model).
**: model equipped with DADF-M1 (outside Japan: iR7086).
***: up graded version
Sub item
PDL-NCSW PDL print job card control mode setting
***
To place the PDL print jobs under the control of the card reader.
When the user asks for the item to be provided
0: PDL printing is performed regardless of whether a card is inserted. [default]
1: PDL printing is not performed when a card has not been inserted or the department ID does not match; PDL printing is performed
when a card has been inserted and when the department ID matches.
PS-MODE Selecting compatibility mode when using PS (image processing, print specification)
This is the mode to simulate REPLACE to hold compatibility for image processing and print specification.
settings
0: no use of PS compatibility mode (default)
1: image processing equivalent of iR2220/2800/3300 series (compatibility with existing machines)
2: image processing equivalent of iR105 (compatibility with existing machine)
3: backup
4: landscape image and portrait image can be duplexed printing using Canon controller. This is the compatible mode with non-Canon
controller.
5 through 65535: backup
When the setting value is '1', the output will be equivalent to that of iR2200 / 2800 / 3300 series. Whereas when the setting value is '2',
the output will be equivalent to that of iR105 series.
CNCT-RLZ Use it to enable/disable the connection serialization function.
Connection serialize function works to secure job grouping function of imageWARE Output Manager Select Edition V1.0. Because
MFP (such as iR machine) is able to gain multiple connections, the job grouping function is secured by setting not to receive multiple
connections at host machine side. If setting '1', it is able to avoid rearrangement of jobs that the machine does not execute job reception
by other connections until the job data reception of a certain connection completes.
settings
0: off (default) ; 1: on
MEMO:
Connection
- connection established among multiple hosts (e.g., PC) via network
Job grouping function
- imageWARE Output Manager Select Edition V1.0 to work not to let a job interruption from other PC by group job (sending multiple
jobs for 1 session when sending jobs)
JA-JOB Designates job archive jobs.
***
When the job archive function is activated, the job archive operates when a job is run, in accordance with the job type designation.
*The settings cannot be changed in service mode, but only referenced.
Settings can only be made from a job archive-enabled MEAP programme.
Setting values
0: None
3: FAX/IFAX only
0xFFFFFFFF: all jobs
[Factory settings and after RAM clear: 0]
JA-RESTR Job archive restriction settings
***
When the job archive function is activated, spec. restrictions are applied against those functions for what spec. restrictions are set.
*The settings cannot be changed in service mode, but only referenced.
Settings can only be made from a job archive-enabled MEAP programme.
Setting values
0, 1
32 spec. restrictions by bit setting.
Bit0: Image file acquisition function (0: OFF, 1: ON)
Bit1: Form registration merge function (0: OFF, 1: ON)
Bit2: Document edit function (0: OFF, 1: ON)
DOM-ADD Use it to set the transmission target domain input complementary switch for mail transmission.
Use it to enable/disable combination of the address entered for transmission with a domain (e.g., @xxx.co.jp) set in user mode.
settings
0: do not combine (default); 1: combine
<when sending mail to aaaa@xxxx.co.jp>
1) Set 'xxxx.co.jp' in the domain in user mode; then, set '1' for the item.
2) At time of transmission, type 'aaaa' so that the address will read 'aaaa@xxxx.co.jp'.
FREE-DSP Charging/non-charging indication switch
***
When a vendor does not have a hardware switch that changes charging/non-charging indication, a software switch is needed. If such
is a case, this mode can be used whether to display the software switch.
0: not display (default)
1: display
CLR-TIM Set the timing of complete deletion of processing data.
***
Select the timing to execute complete deletion using the security kit.
When complete deletion is executed, performance of job processing may decrease depending on the data. This occurs because
processed page data is deleted during job processing and much load is applied to the processing to access the CPU or HDD. When this
processing is performed after job processing is completed, job processing capability can be improved.
Setting range: 0, 1 (0: Delete data during job processing. 1: Delete data after job processing is completed.)
Factory setting value: 0
17-78
COPIER > OPTION > USER
Description Level
2
2
2
2
2
2
2
2