Siemens SINAMICS S150 Operating Instructions Manual page 502

Appendix
A.2 Parameter macros
Parameter
p2051[4] CI: PROFIBUS PZD send word
p2051[5] CI: PROFIBUS PZD send word
p2080[0] BI: PROFIBUS send status word 1
p2080[1] BI: PROFIBUS send status word 1
p2080[2] BI: PROFIBUS send status word 1
p2080[3] BI: PROFIBUS send status word 1
p2080[4] BI: PROFIBUS send status word 1
p2080[5] BI: PROFIBUS send status word 1
p2080[6] BI: PROFIBUS send status word 1
p2080[7] BI: PROFIBUS send status word 1
p2080[8] BI: PROFIBUS send status word 1
p2080[9] BI: PROFIBUS send status word 1
p2080[10] BI: PROFIBUS send status word 1
p2080[11] BI: PROFIBUS send status word 1
p2080[12] BI: PROFIBUS send status word 1
p2080[13] BI: PROFIBUS send status word 1
p2080[14] BI: PROFIBUS send status word 1
p2080[15] BI: PROFIBUS send status word 1
p2088 PROFIBUS Invert status word
p2128[14] Select fault/alarm code for trigger
p2128[15] Select fault/alarm code for trigger
p2153 Speed actual value filter time constant
p0840[0] ON/OFF 1
p2105 BI: 3. Acknowledge faults
p1207 BI: WEA link, following DO
p4053[0] TM31 analog inputs, smoothing time
constant
p4053[1] TM31 analog inputs, smoothing time
constant
p4056[0] TM31 analog inputs, type
p4056[1] TM31 analog inputs, type
p4076[0] TM31 analog outputs, type
p4076[1] TM31 analog outputs, type
p4071[0] Signal analog output 0
p4071[1] Signal analog output 1
p4100 TM31 temperature evaluation, sensor
type
p4102[0] TM31 temperature evaluation
fault/alarm threshold
p4102[1] TM31 temperature evaluation
fault/alarm threshold
502
Sink
Description DO Parameter
Vector r0082 P-act
Vector r2131 FAULT
Vector r0899[0] Ready to power up
Vector r0899[1] Ready
Vector r0899[2] Operation enabled
Vector r2139[3] Fault
Vector r0899[4] No OFF2
Vector r0899[5] No OFF3
Vector r0899[6] Power-on inhibit
Vector r2139[7] Alarm present
Vector r2197[7] Setpoint/actual value deviation in
tolerance
Vector r0899[9] Control from PLC
Vector r2199[1] Comparison value reached
Vector r1407[7] M/I/P limiting not active
Vector 0
Vector r2129[14] No alarm for motor overtemperature
Vector r2197[3] Clockwise
Vector r2129[15] No alarm for therm. overload of power
unit
Vector B800h
Vector 7910 Alarm, motor overtemperature
Vector 5000 Alarm for therm. overload of power
unit
Vector 20 ms
A_INF r0863.1 Energize line contactor
A_INF r1214.3 Automatic restart status – set
acknowledgement command
A_INF r1214.2 Automatic restart status – restart
active
TM31 0 ms
TM31
TM31 2 Current 0...20 mA
TM31 2 Current 0...20 mA
TM31 0 Current 0...20 mA
TM31 0 Current 0...20 mA
TM31 r0063 Actual speed smoothed
TM31 r0068 Absolute current actual value
TM31 0 (Factory setting)
TM31 251°C Message being generated
TM31 251°C Message being generated
Source
Description
Drive converter cabinet units
Operating Instructions, 07/07, A5E00288214A
DO
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
TM31
TM31
TM31
TM31
TM31
TM31
TM31
TM31
TM31
TM31
TM31