Table of Contents
Advertisement
Copyright © 2010, Juniper Networks, Inc.
1) Install Device Server only
2) Install GUI Server only
3) Install both Device Server and GUI Server
Enter selection (1-3) []> 3
The installer prompts you to specify the components that you want to install. Enter
4.
3 to specify that you want to install both the GUI Server and the Device Server.
NOTE: If you have installed a previous version of the management system,
you might see different menu options.
Do you want to do NSM installation with base license? (y/n) [y]>
Enter base directory location for management servers [/usr/netscreen]>
For a base license installation—that is, one that does not require the license key
5.
file—enter y.
For an installation that requires a license key file, enter n. You enter the license file
path later. See "Generating the NSM License Key File" on page 13 for information
about obtaining license keys.
The installer prompts you to specify a base directory in which to install the
6.
management server files.
Press Enter to accept the default
to a directory and then press Enter.
The installer prompts whether you want to enable FIPS support.
If you require FIPS support, enter y. Otherwise, press Enter to accept the default value.
7.
What happens next depends on whether you selected to install with a base license
or with a license key file. If you are installing with a base license, skip step 8.
If you chose to install a license key file, the installer displays the installation ID of the
8.
system and prompts you to enter the license key file path.
The installation ID for this system is: 3FFFEA90278AA
Enter the License File Path>
a. Use the installation ID to obtain a license key file from the LMS system and save
it on your local drive as described in "Generating the License Key for an NSM
Software-Only Installation" on page 14.
b. Enter the license key file path.
The installer validates the license key file.
Chapter 3: Installing NSM in a Standalone Configuration
directory, or type the full path name
/usr/netscreen
31
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - INSTALLATION GUIDE REV1
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - INSTALLATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW CONTROLLER 2.0.4 -
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - EVENT CATEGORY CORRELATION REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - SNMP AGENT GUIDE REV 1
- Juniper STRM LOG MANAGEMENT 2008.2 - S 6-2008
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - INSTALLATION GUIDE REV1 and is the answer not in the manual?