Table of Contents
Advertisement
Network and Security Manager Installation Guide
Upgrading to NSM 2010.4 Release on an NSM Appliance (Offline Mode)
160
Sets start scripts.
Performs postinstallation tasks such as removing the staging directory and starting
the server processes (if configured).
Messages display the installation progress.
After the installation script finishes, it generates a log file with the output of the
installation commands for troubleshooting. The installer indicates the name of the
installation log file and the directory location where it is saved. This file is saved by
default in the
/usr/netscreen/GuiSvr/var/errorLog
After successful installation, copy the installer file
13.
directory and enter the following commands:
/var/install
rm -f NSM-CM
chmod 755 nsm2010.4_servers_cm.sh
ln -s nsm2010.4_servers_linux_cm.sh NSM-CM
The section provides instructions on upgrading to NSM 2010.4 on an NSM appliance if
the NSM appliance is not connected to the Internet.
From the NSM Software Download page, click the Regional Server upgrade link to
1.
download the NSM Appliance upgrade software. The downloaded file has the name
nsm2010.4_servers_upgrade_rs.zip
From the NSM Software Download page, click the Offline Server upgrade link to
2.
download the NSM Appliance offline upgrade software. The downloaded file has the
name
nsm2010.4_offline_upgrade.zip
Copy the following files onto your NSM appliance. Download both files to the same
3.
location using FTP or SCP.
nsm2010.4_servers_upgrade_rs.zip
nsm2010.4_offline_upgrade.zip
Log in as the admin user, and answer n when prompted to run the setup wizard.
4.
Enter the following command, and then enter the admin password to gain root access.
5.
sudo su -
Confirm that the
utility is present on the NSM appliance by entering the following
unzip
6.
command:
which unzip
This command returns the location of the
utility is provided on the NSM Software Download page. Use the following command
to install this utility:
rpm –i unzip-5.51-9.EL4.5.i386.rpm
Navigate to the directory where you saved the downloaded files, which is typically
7.
the
subdirectory.
/tmp/
subdirectory.
nsm2010.4_servers_cm.sh
.
.
unzip
utility. If it is not available, the
Copyright © 2010, Juniper Networks, Inc.
to the
unzip
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - INSTALLATION GUIDE REV1
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - INSTALLATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW CONTROLLER 2.0.4 -
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - EVENT CATEGORY CORRELATION REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - SNMP AGENT GUIDE REV 1
- Juniper STRM LOG MANAGEMENT 2008.2 - S 6-2008
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - INSTALLATION GUIDE REV1 and is the answer not in the manual?