Table of Contents
Advertisement
Copyright © 2010, Juniper Networks, Inc.
Enter the following command to unzip the files (
8.
) and create a directory (
upgrade-os.sh
files.
unzip nsm2010.4_servers_upgrade_rs.zip
Enter the following command to start the installation.
9.
sh upgrade-os.sh nsm2010.4_servers_linux_x86.sh Offline
The installer begins a series of preinstallation checks that ensure:
You are installing the correct software for your operating system.
All the necessary software binaries are present.
You correctly logged in as root.
You have installed a version of NSM earlier than the current version you are installing.
The system has sufficient disk space and RAM.
NOTE: The management system installer indicates the results of its
specific tasks and checks:
"Done" indicates that the installer successfully performed a task.
"OK" indicates that the installer performed a check and verified that the
condition was satisfied.
"FAILED" indicates that the installer performed a task or check, but it
was not successful. See the install log for information about the failure.
This log is usually stored in
failure happens in the early stages of installation, the log might be in
.
/tmp
The installer then stops any running servers.
Type 2 to specify that you want to upgrade both the Device Server and the GUI Server.
10.
NOTE: If you specify that you want to upgrade the Device Server and the
GUI Server, all data previously configured in the system is restored. If you
do not want to restore your previous configuration data, choose to have
the installer perform a clean install of NSM.
The installer next prompts you to configure additional options specific to your
11.
installation during the upgrade. These options can include:
Configuring high availability
Configuring interoperability with NetScreen Statistical Report Server
Chapter 7: Upgrading NSM Appliances to NSM 2010.4
nsm2010.4_servers_linux_x86.sh
) in which NSM saves the unzipped
apps-rpms
/usr/netscreen/DevSvr/var/errorLog
,
. If the
161
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - INSTALLATION GUIDE REV1
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - INSTALLATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW CONTROLLER 2.0.4 -
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - EVENT CATEGORY CORRELATION REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - SNMP AGENT GUIDE REV 1
- Juniper STRM LOG MANAGEMENT 2008.2 - S 6-2008
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - INSTALLATION GUIDE REV1 and is the answer not in the manual?
Questions and answers