Table of Contents
Advertisement
Program mode: HD-1
If there is distortion, but the "ADC OVERLOAD!" message
does not appear, it's possible that the distortion is being
caused by the settings of the internal effects. To solve this
problem, either lower the input Level (see "Level," above),
or adjust the effects settings (such as changing the individual
effect Input Trim parameters).
0–8c: Sampling Setup
Source Bus
You can sample in stereo from any pair of audio inputs, from
the two stereo REC busses, or from the signal at any of the 6
outputs (L/R and Individual 1/2-3/4).
When you sample from an output pair or REC bus, you'll
record all audio sent to the output or bus, including internal
Programs or Combis, effects, audio inputs, and HDR audio.
When sampling in stereo, the odd-numbered channel (such
as 1 or 3) corresponds to the left channel, and the even-
numbered channel (such as 2 or 4) corresponds to the right.
L/R: This lets you sample the signal heard at the main L/R
outputs, including any processing by TFX 1/2. This is the
default setting. For more information, see the diagram
"Source Bus = L/R" on page 22.
REC1/2, REC3/4: These let you sample the signals sent to
the REC 1/2 or REC 3/4 busses.
Source Bus = L/R
Source Bus = L/R
Audio Inputs
OSC
Source Bus = REC Bus 1/2
Source Bus = REC Bus 1/2
Audio Inputs
OSC
22
[Audio Input1/2, USB 1/2,
S/P DIF L/R, L/R,
REC1/2...3/4, Indiv.1/2...3/4]
L/R
REC
Bus
1/2
Insert
Effects
Level
Pan
Insert
Effects
Bus = L/R or IFX1-12
L/R
REC
Bus
1/2
REC Bus = 1/2
Insert
Effects
Level
Pan
Insert
Effects
Bus = L/R or IFX1-12
Using the REC busses, you can isolate one or more sounds
for recording or sampling–even if the sounds are also being
mixed into the main outputs. For example, you can play a
guitar through KRONOS IFX while listening to a KARMA
drum phrase, and record the processed guitar without
recording the drums.
Individual Programs, Combi Timbres, Sequencer Tracks
(both MIDI and Audio), audio inputs, and Insert Effects can
all be routed to the REC busses, in addition to their main
output/IFX bus settings.
For more information, see the diagram "Source Bus = REC
Bus 1/2" on page 22.
Audio Input 1/2, S/P DIF L/R, USB: These let you sample
directly from the analog, S/P DIF, or USB audio inputs,
respectively, without any other processing by KRONOS.
The settings on the Audio Inputs mixer, including volume,
pan, busses, sends, mute, and solo, will have no effect on the
recorded audio.
For more information, see the diagram "Source Bus = Audio
Input 1/2" on page 23.
For more information, see the diagram "Source Bus = USB
1/2" on page 23.
Indiv.1/2...3/4: This lets you sample the individual output
busses. For more information, see the diagram "Source Bus
= Indiv. 1/2" on page 23.
REC
Indiv.
3/4
3/4
1/2
Master
Effects
Total
Effects
REC
Indiv.
1/2
3/4
3/4
Master
Effects
Total
Effects
[x] Source Direct Solo
CLIP !!
Sampling
L-Mono
R-Mono Stereo
Monitor
L/MONO
AUDIO OUTPUT
HEADPHONES
R
CLIP !!
Sampling
L-Mono
R-Mono Stereo
Monitor
L/MONO
AUDIO OUTPUT
HEADPHONES
R
Advertisement
Table of Contents
