Canon imageRUNNER ADVANCE C3330 Series Service Manual page 780

COPIER (Service mode for copier) > ADJUST (Adjustment mode) > HV-TR
TR-ENV4 2
Detail
Use Case
Adj/Set/Operate Method
Display/Adj/Set Range
Default Value
Related Service Mode
Supplement/Memo
TR-ENV5 2
Detail
Use Case
Adj/Set/Operate Method
Display/Adj/Set Range
Default Value
Related Service Mode
Supplement/Memo
TR-ENV6 2
Detail
Use Case
Adj/Set/Operate Method
Display/Adj/Set Range
Default Value
Related Service Mode
Supplement/Memo
Sec trns indiv setting environment:set 4
To set the environment (absolute moisture content) for setting 4.
Setting 4 is the combination condition of environment, paper type (paper weight), color mode/feed
side that are set in TR-ENV4, TR-PPR4 and TR-DUP4. When this condition is satisfied, the paper
allotted voltage adjusted in TR-VL4 is applied at the time of secondary transfer.
When an image failure that differs due to the environment occurs (mottled image/density loss due
to excessive transfer/toner scattering on solid image, etc.)
Enter the setting value, and then press OK key.
1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2: Normal humidity (6.12 to 15.68
g/m3), 3: High humidity (15.69 g/m3 or higher)
1
COPIER> ADJUST> HV-TR> TR-PPR4, TR-DUP4, TR-VL4, 2TR-OFF
Up to 16 combination patterns can be set in TR-VL1 to 16 (setting 1 to 16). When there is more
than one setting where all conditions (environment, paper type and color mode/feed side) are the
same, the setting with a smaller setting number is applied.
Sec trns indiv setting environment:set 5
To set the environment (absolute moisture content) for setting 5.
Setting 5 is the combination condition of environment, paper type (paper weight), color mode/feed
side that are set in TR-ENV5, TR-PPR5 and TR-DUP5. When this condition is satisfied, the paper
allotted voltage adjusted in TR-VL5 is applied at the time of secondary transfer.
When an image failure that differs due to the environment occurs (mottled image/density loss due
to excessive transfer/toner scattering on solid image, etc.)
Enter the setting value, and then press OK key.
1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2: Normal humidity (6.12 to 15.68
g/m3), 3: High humidity (15.69 g/m3 or higher)
1
COPIER> ADJUST> HV-TR> TR-PPR5, TR-DUP5, TR-VL5, 2TR-OFF
Up to 16 combination patterns can be set in TR-VL1 to 16 (setting 1 to 16). When there is more
than one setting where all conditions (environment, paper type and color mode/feed side) are the
same, the setting with a smaller setting number is applied.
Sec trns indiv setting environment:set 6
To set the environment (absolute moisture content) for setting 6.
Setting 6 is the combination condition of environment, paper type (paper weight), color mode/feed
side that are set in TR-ENV6, TR-PPR6 and TR-DUP6. When this condition is satisfied, the paper
allotted voltage adjusted in TR-VL6 is applied at the time of secondary transfer.
When an image failure that differs due to the environment occurs (mottled image/density loss due
to excessive transfer/toner scattering on solid image, etc.)
Enter the setting value, and then press OK key.
1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2: Normal humidity (6.12 to 15.68
g/m3), 3: High humidity (15.69 g/m3 or higher)
1
COPIER> ADJUST> HV-TR> TR-PPR6, TR-DUP6, TR-VL6, 2TR-OFF
Up to 16 combination patterns can be set in TR-VL1 to 16 (setting 1 to 16). When there is more
than one setting where all conditions (environment, paper type and color mode/feed side) are the
same, the setting with a smaller setting number is applied.
768
8. Service Mode