Canon imageRUNNER ADVANCE C3330 Series Service Manual page 793

COPIER (Service mode for copier) > ADJUST (Adjustment mode) > HV-TR
TR-ENV9 2
Detail
Use Case
Adj/Set/Operate Method
Display/Adj/Set Range
Default Value
Related Service Mode
Supplement/Memo
TR-ENV10 2
Detail
Use Case
Adj/Set/Operate Method
Display/Adj/Set Range
Default Value
Related Service Mode
Supplement/Memo
TR-ENV11 2
Detail
Use Case
Adj/Set/Operate Method
Display/Adj/Set Range
Default Value
Related Service Mode
Supplement/Memo
Sec trns indiv setting environment:set 9
To set the environment (absolute moisture content) for setting 9.
Setting 9 is the combination condition of environment, paper type (paper weight), color mode/feed
side that are set in TR-ENV9, TR-PPR9 and TR-DUP9. When this condition is satisfied, the paper
allotted voltage adjusted in TR-VL9 is applied at the time of secondary transfer.
When an image failure that differs due to the environment occurs (mottled image/density loss due
to excessive transfer/toner scattering on solid image, etc.)
Enter the setting value, and then press OK key.
1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2: Normal humidity (6.12 to 15.68
g/m3), 3: High humidity (15.69 g/m3 or higher)
1
COPIER> ADJUST> HV-TR> TR-PPR9, TR-DUP9, TR-VL9, 2TR-OFF
Up to 16 combination patterns can be set in TR-VL1 to 16 (setting 1 to 16). When there is more
than one setting where all conditions (environment, paper type and color mode/feed side) are the
same, the setting with a smaller setting number is applied.
Sec trn indiv setting environment:set 10
To set the environment (absolute moisture content) for setting 10.
Setting 10 is the combination condition of environment, paper type (paper weight), color mode/
feed side that are set in TR-ENV10, TR-PPR10 and TR-DUP10. When this condition is satisfied,
the paper allotted voltage adjusted in TR-VL10 is applied at the time of secondary transfer.
When an image failure that differs due to the environment occurs (mottled image/density loss due
to excessive transfer/toner scattering on solid image, etc.)
Enter the setting value, and then press OK key.
1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2: Normal humidity (6.12 to 15.68
g/m3), 3: High humidity (15.69 g/m3 or higher)
1
COPIER> ADJUST> HV-TR> TR-PPR10, TR-DUP10, TR-VL10, 2TR-OFF
Up to 16 combination patterns can be set in TR-VL1 to 16 (setting 1 to 16). When there is more
than one setting where all conditions (environment, paper type and color mode/feed side) are the
same, the setting with a smaller setting number is applied.
Sec trn indiv setting environment:set 11
To set the environment (absolute moisture content) for setting 11.
Setting 11 is the combination condition of environment, paper type (paper weight), color mode/
feed side that are set in TR-ENV11, TR-PPR11 and TR-DUP11. When this condition is satisfied,
the paper allotted voltage adjusted in TR-VL11 is applied at the time of secondary transfer.
When an image failure that differs due to the environment occurs (mottled image/density loss due
to excessive transfer/toner scattering on solid image, etc.)
Enter the setting value, and then press OK key.
1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2: Normal humidity (6.12 to 15.68
g/m3), 3: High humidity (15.69 g/m3 or higher)
1
COPIER> ADJUST> HV-TR> TR-PPR11, TR-DUP11, TR-VL11, 2TR-OFF
Up to 16 combination patterns can be set in TR-VL1 to 16 (setting 1 to 16). When there is more
than one setting where all conditions (environment, paper type and color mode/feed side) are the
same, the setting with a smaller setting number is applied.
781
8. Service Mode