Canon imageRUNNER ADVANCE C3330 Series Service Manual page 779

COPIER (Service mode for copier) > ADJUST (Adjustment mode) > HV-TR
TR-ENV1 2
Detail
Use Case
Adj/Set/Operate Method
Display/Adj/Set Range
Default Value
Related Service Mode
Supplement/Memo
TR-ENV2 2
Detail
Use Case
Adj/Set/Operate Method
Display/Adj/Set Range
Default Value
Related Service Mode
Supplement/Memo
TR-ENV3 2
Detail
Use Case
Adj/Set/Operate Method
Display/Adj/Set Range
Default Value
Related Service Mode
Supplement/Memo
Sec trns indiv setting environment:set 1
To set the environment (absolute moisture content) for setting 1.
Setting 1 is the combination condition of environment, paper type (paper weight), color mode/feed
side that are set in TR-ENV1, TR-PPR1 and TR-DUP1. When this condition is satisfied, the paper
allotted voltage adjusted in TR-VL1 is applied at the time of secondary transfer.
When an image failure that differs due to the environment occurs (mottled image/density loss due
to excessive transfer/toner scattering on solid image, etc.)
Enter the setting value, and then press OK key.
1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2: Normal humidity (6.12 to 15.68
g/m3), 3: High humidity (15.69 g/m3 or higher)
1
COPIER> ADJUST> HV-TR> TR-PPR1, TR-DUP1, TR-VL1, 2TR-OFF
Up to 16 combination patterns can be set in TR-VL1 to 16 (setting 1 to 16). When there is more
than one setting where all conditions (environment, paper type and color mode/feed side) are the
same, the setting with a smaller setting number is applied.
Sec trns indiv setting environment:set 2
To set the environment (absolute moisture content) for setting 2.
Setting 2 is the combination condition of environment, paper type (paper weight), color mode/feed
side that are set in TR-ENV2, TR-PPR2 and TR-DUP2. When this condition is satisfied, the paper
allotted voltage adjusted in TR-VL2 is applied at the time of secondary transfer.
When an image failure that differs due to the environment occurs (mottled image/density loss due
to excessive transfer/toner scattering on solid image, etc.)
Enter the setting value, and then press OK key.
1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2: Normal humidity (6.12 to 15.68
g/m3), 3: High humidity (15.69 g/m3 or higher)
1
COPIER> ADJUST> HV-TR> TR-PPR2, TR-DUP2, TR-VL2, 2TR-OFF
Up to 16 combination patterns can be set in TR-VL1 to 16 (setting 1 to 16). When there is more
than one setting where all conditions (environment, paper type and color mode/feed side) are the
same, the setting with a smaller setting number is applied.
Sec trns indiv setting environment:set 3
To set the environment (absolute moisture content) for setting 3.
Setting 3 is the combination condition of environment, paper type (paper weight), color mode/feed
side that are set in TR-ENV3, TR-PPR3 and TR-DUP3. When this condition is satisfied, the paper
allotted voltage adjusted in TR-VL3 is applied at the time of secondary transfer.
When an image failure that differs due to the environment occurs (mottled image/density loss due
to excessive transfer/toner scattering on solid image, etc.)
Enter the setting value, and then press OK key.
1 to 3
1: Low humidity (absolute moisture content: 6.11 g/m3 or less), 2: Normal humidity (6.12 to 15.68
g/m3), 3: High humidity (15.69 g/m3 or higher)
1
COPIER> ADJUST> HV-TR> TR-PPR3, TR-DUP3, TR-VL3, 2TR-OFF
Up to 16 combination patterns can be set in TR-VL1 to 16 (setting 1 to 16). When there is more
than one setting where all conditions (environment, paper type and color mode/feed side) are the
same, the setting with a smaller setting number is applied.
767
8. Service Mode