Canon imageRUNNER ADVANCE C3330 Series Service Manual page 907

COPIER (Service mode for copier) > OPTION (Specification setting mode) > IMG-FIX
TMP-TB11 1
Detail
Use Case
Adj/Set/Operate Method
Caution
Display/Adj/Set Range
Unit
Default Value
Amount of Change per
Unit
FXS-TM11 1
Detail
Use Case
Adj/Set/Operate Method
Caution
Display/Adj/Set Range
Unit
Default Value
Amount of Change per
Unit
PLN-LP 2
Detail
Use Case
Adj/Set/Operate Method
Display/Adj/Set Range
Default Value
TRC-LP 2
Detail
Use Case
Adj/Set/Operate Method
Display/Adj/Set Range
Default Value
Set fixing control temp:recycled paper 1
To set the offset of fixing control temperature for recycled paper 1 (64 to 75 g/m2).
As the value is changed by 1, the control temperature is changed by 5 deg C.
Increase the value when a fixing failure occurs, and decrease the value when fixing offset occurs.
When a fixing failure/fixing offset occurs on recycled paper 1
Enter the setting value (switch negative/positive by -/+ key) and press OK key.
Be sure to change the value a little at a time. Otherwise, offset/image failure occurs when setting
an extreme value.
-3 to 2
-3: -15 deg C, -2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
deg C
0
5
Set ITOP control temp: recycled paper 1
To set the offset of ITOP control temperature for recycled paper 1 (64 to 75 g/m2).
As the value is changed by 1, the control temperature is changed by 5 deg C.
Decrease the value when uneven gloss occurs, and increase the value when a fixing failure occurs
on the leading edge of paper.
- When a fixing failure occurs on the leading edge of paper
- When uneven gloss occurs on the leading edge (74 mm)
Enter the setting value (switch negative/positive by -/+ key) and press OK key.
If the value is too large, uneven gloss may occur.
If the value is too small, a fixing failure may occur on the leading edge of paper. (Toner does not
peel off.)
-3 to 2
-3: -15 deg C, -2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
deg C
0
5
Set fix arch ctrl: pln,color,rcycl,punch
To set the arch amount between the secondary transfer and fixing when feeding plain paper 1/2/3,
colored paper, recycled paper 1/2/3 and pre-punched paper at 1/1 speed.
Increase the value when an image failure (crawled marks/wrinkles) occurs.
When an image failure (crawled marks/wrinkles) occurs with plain paper, colored paper, recycled
paper and pre-punched paper
Enter the setting value (switch negative/positive by -/+ key) and press OK key.
-2 to 2
-2: 0 mm, -1: 15 mm, 0: 35 mm, 1: 60 mm, 2: 85 mm
0
Set fixing arch control: tracing paper
To set the arch amount between the secondary transfer and fixing when feeding tracing paper at
1/1 speed.
Increase the value when an image failure (crawled marks/wrinkles) occurs.
When an image failure (crawled marks/wrinkles) occurs with tracing paper
Enter the setting value (switch negative/positive by -/+ key) and press OK key.
-2 to 2
-2: 0 mm, -1: 15 mm, 0: 35 mm, 1: 60 mm, 2: 85 mm
0
895
8. Service Mode