Canon imageRUNNER ADVANCE C3330 Series Service Manual page 790

COPIER (Service mode for copier) > ADJUST (Adjustment mode) > HV-TR
TR-PPR11 2
Detail
Use Case
Adj/Set/Operate Method
Display/Adj/Set Range
Default Value
Related Service Mode
Supplement/Memo
TR-PPR12 2
Detail
Use Case
Adj/Set/Operate Method
Display/Adj/Set Range
Default Value
Related Service Mode
Supplement/Memo
Sec trn indiv setting paper type: set 11
To set the paper type (paper weight) for setting 11.
Setting 11 is the combination condition of environment, paper type (paper weight), color mode/
feed side that are set in TR-ENV11, TR-PPR11 and TR-DUP11. When this condition is satisfied,
the paper allotted voltage adjusted in TR-VL11 is applied at the time of secondary transfer.
When an image failure that differs due to the paper type occurs (mottled image/density loss due
to excessive transfer/toner scattering on solid image, etc.)
Enter the setting value, and then press OK key.
1 to 25
1: Plain paper 1 (64 to 75 g/m2), 2: Plain paper 2 (76 to 90 g/m2)/Colored paper (64 to 82 g/m2),
3: Plain paper 3 (91 to 105 g/m2), 4: Recycled paper 1 (64 to 75 g/m2), 5: Recycled paper 2 (76
to 90 g/m2), 6: Recycled paper 3 (91 to 105 g/m2), 7: Thin paper (52 to 63 g/m2), 8: Heavy paper
1 (106 to 128 g/m2), 9: Heavy paper 2 (129 to 163 g/m2), 10: Heavy paper 3 (164 to 220 g/m2),
11: Heavy paper 4 (221 to 256 g/m2), 12: 1-sided coated paper 1 (106 to 128 g/m2), 13: 1-sided
coated paper 2 (129 to 163 g/m2), 14: 1-sided coated paper 3 (164 to 220 g/m2), 15: 2-sided
coated paper 1 (106 to 128 g/m2), 16: 2-sided coated paper 2 (129 to 163 g/m2), 17: 2-sided
coated paper 3 (164 to 220 g/m2), 18: Tracing paper (64 to 99 g/m2), 19: Transparency (121 to
220 g/m2), 20: Envelope (75 to 105 g/m2), 21: Postcard (164 to 220 g/m2), 22: Label (118 to 185
g/m2), 23: Pre-punched paper (64 to 75 g/m2), 24: Bond paper (83 to 99 g/m2), 25: Not used
1
COPIER> ADJUST> HV-TR> TR-ENV11, TR-DUP11, TR-VL11, 2TR-OFF
Up to 16 combination patterns can be set in TR-VL1 to 16 (setting 1 to 16). When there is more
than one setting where all conditions (environment, paper type and color mode/feed side) are the
same, the setting with a smaller setting number is applied.
Sec trn indiv setting paper type: set 12
To set the paper type (paper weight) for setting 12.
Setting 12 is the combination condition of environment, paper type (paper weight), color mode/
feed side that are set in TR-ENV12, TR-PPR12 and TR-DUP12. When this condition is satisfied,
the paper allotted voltage adjusted in TR-VL12 is applied at the time of secondary transfer.
When an image failure that differs due to the paper type occurs (mottled image/density loss due
to excessive transfer/toner scattering on solid image, etc.)
Enter the setting value, and then press OK key.
1 to 25
1: Plain paper 1 (64 to 75 g/m2), 2: Plain paper 2 (76 to 90 g/m2)/Colored paper (64 to 82 g/m2),
3: Plain paper 3 (91 to 105 g/m2), 4: Recycled paper 1 (64 to 75 g/m2), 5: Recycled paper 2 (76
to 90 g/m2), 6: Recycled paper 3 (91 to 105 g/m2), 7: Thin paper (52 to 63 g/m2), 8: Heavy paper
1 (106 to 128 g/m2), 9: Heavy paper 2 (129 to 163 g/m2), 10: Heavy paper 3 (164 to 220 g/m2),
11: Heavy paper 4 (221 to 256 g/m2), 12: 1-sided coated paper 1 (106 to 128 g/m2), 13: 1-sided
coated paper 2 (129 to 163 g/m2), 14: 1-sided coated paper 3 (164 to 220 g/m2), 15: 2-sided
coated paper 1 (106 to 128 g/m2), 16: 2-sided coated paper 2 (129 to 163 g/m2), 17: 2-sided
coated paper 3 (164 to 220 g/m2), 18: Tracing paper (64 to 99 g/m2), 19: Transparency (121 to
220 g/m2), 20: Envelope (75 to 105 g/m2), 21: Postcard (164 to 220 g/m2), 22: Label (118 to 185
g/m2), 23: Pre-punched paper (64 to 75 g/m2), 24: Bond paper (83 to 99 g/m2), 25: Not used
1
COPIER> ADJUST> HV-TR> TR-ENV12, TR-DUP12, TR-VL12, 2TR-OFF
Up to 16 combination patterns can be set in TR-VL1 to 16 (setting 1 to 16). When there is more
than one setting where all conditions (environment, paper type and color mode/feed side) are the
same, the setting with a smaller setting number is applied.
778
8. Service Mode