Mitsubishi Electric GOT2000 Series Hardware User Manual page 132

Part names and settings of GT25-S and GT25-V
No. Name
1) Display section
2) Touch panel
3) USB interface (Host/front)
4) USB interface (Device/front)
5) POWER LED
7) Unit installation fitting
8) Reset switch
9) S.MODE switch
10) SD card access LED
11) SD card interface (inside the cover)
12) SD card cover
13) Battery (inside the cover)
14) Side interface (inside the cover)
15) USB interface (Host/back)
16) Cable clamp mounting hole
17) Terminating resistor setting switch (inside
the cover)
19) Extension interface
20) Vertical installation arrow mark
21) Power terminal
22) Ethernet interface
23) Ethernet communication status LED
24) RS-232 interface
25) RS-422/485 interface
26) USB interface (Device/back)
27) Fitting installation hole
28) Special fitting installation hole
29) Rating plate
4 PART NAMES AND SETTINGS
130
4.4 GT25-S, GT25-V
Description
Displays the utility and the user-created screen.
For operating the touch switches in the utility and the user-created screen
For connecting a USB mouse, a USB keyboard, or a USB barcode reader, and transferring or saving data
(Connector shape: USB-A)
Applicable models: GT2512-STBA/D, GT2510-VTBA/D, GT2508-VTBA/D
For connecting a personal computer (Connector shape: USB Mini-B)
Applicable models: GT2512-STBA/D, GT2510-VTBA/D, GT2508-VTBA/D, GT2505-V
Lit in blue: Power is properly supplied.
Lit in orange: Screen saving
Blinks in orange and blue: Backlight failure
Not lit: Power is not supplied.
(For GT2512F-STNA/D, GT2510F-VTNA/D, and GT2508F-VTNA/D, you can check the LED status from
the GOT rear face.)
Mounting fixtures for fixing the GOT to the control panel
Hardware reset switch
*3
Used for OS installation at the GOT startup
ON: SD card installed
Blink: SD card accessed
OFF: SD card not installed or SD card installed but removal possible
For installing an SD card
Has the function to switch the access to the SD card between enabled and disabled states.
When the cover is opened: Access prohibited
When the cover is closed: Access allowed
Space for housing the battery
For installing a communication unit
For connecting a USB mouse, a USB keyboard, or a USB barcode reader, and transferring or saving data
(Connector shape: USB-A)
Cable clamp mounting hole as a precaution against a disconnection of the USB cable
• GT2512, GT2510, GT2508
Switches the terminating resistor for the RS-422/485 communication port between used and unused
states (initial setting (unused))
• GT2505-V
For switching the terminating resistor setting of the RS-422/485 communication port to 330 Ω, 110 Ω, or
OPEN (Default: 330 Ω)
For installing a communication unit or an option unit
For the vertical installation, install the GOT so that the arrow points upward.
Power input terminal, FG terminal, LG terminal
For communicating with a controller or connecting a personal computer (Connector shape: RJ-45
(modular jack))
SD/RD LED ON: Data sent or received
SD/RD LED OFF: Data not sent or received
SPEED LED ON: Communicating at 100 Mbps
SPEED LED OFF: Communicating at 10 Mbps or disconnected
For communication with a controller (Connector shape: D-sub 9-pin (male))
For the pin layout of the connector, refer to the following.
GOT2000 Series Connection Manual (Mitsubishi Electric Products) For GT Works3 Version1
For communication with a controller (Connector shape: D-sub 9-pin (female))
For the pin layout of the connector, refer to the following.
GOT2000 Series Connection Manual (Mitsubishi Electric Products) For GT Works3 Version1
For connecting a personal computer (Connector shape: USB Mini-B)
Applicable models: GT2512F-STNA/D, GT2510-VTWA/D, GT2510F-VTNA/D, GT2508-VTWA/D,
GT2508F-VTNA/D
For fixing the fitting to the control panel
Applicable models: GT2512F-STNA/D, GT2510F-VTNA/D, and GT2508F-VTNA/D
*1
For fixing the GOT to the control panel to comply with the ATEX directive and KCs regulation
Applicable model: GT2510-VTWA/D
—
*2