Canon imageRUNNER ADVANCE C3500 III Series Service Manual page 698

8. Service Mode
COPIER (Service mode for printer) > ADJUST (Adjustment mode) > HV-TR
TR-PPR10 2 Sec trn indiv setting paper type: set 10
Detail To set the paper type (paper weight) for setting 10.
Setting 10 is the combination condition of environment, paper type (paper weight), color mode/
feed side that are set in TR-ENV10, TR-PPR10 and TR-DUP10. When this condition is satisfied,
the paper allotted voltage adjusted in TR-VL10 is applied at the time of secondary transfer.
Use Case When an image failure that differs due to the paper type occurs (mottled image/density loss due
to excessive transfer/toner scattering on solid image, etc.)
Adj/Set/Operate Method Enter the setting value, and then press OK key.
Caution The setting values 20 (1-sided coated paper 5) and 25 (2-sided coated paper 5) can be set only
when the Media Adjustment Kit is connected in the location where it can be used.
Display/Adj/Set Range
1 to 33
1: Plain paper 1 (64 to 75 g/m2), 2: Plain paper 2 (76 to 90 g/m2)/Colored paper 1 (64 to 82 g/m2),
3: Plain paper 3 (91 to 105 g/m2)
4: Recycled paper 1 (64 to 75 g/m2), 5: Recycled paper 2 (76 to 90 g/m2), 6: Recycled paper 3
(91 to 105 g/m2)
7: Thin paper 2 (52 to 59 g/m2), 8: Thin paper 1 (60 to 63 g/m2)
9: Heavy paper 1 (106 to 128 g/m2), 10: Heavy paper 2 (129 to 150 g/m2), 11: Heavy paper 3 (151
to 163 g/m2), 12: Heavy paper 4 (164 to 180 g/m2), 13: Heavy paper 5 (181 to 220 g/m2), 14:
Heavy paper 6 (221 to 256 g/m2), 15: Heavy paper 7 (257 to 300 g/m2)
16: 1-sided coated paper 1 (106 to 128 g/m2), 17: 1-sided coated paper 2 (129 to 163 g/m2), 18:
1-sided coated paper 3 (164 to 220 g/m2), 19: 1-sided coated paper 4 (221 to 256 g/m2), 20: 1-
sided coated paper 5 (257 to 300 g/m2)
21: 2-sided coated paper 1 (106 to 128 g/m2), 22: 2-sided coated paper 2 (129 to 163 g/m2), 23:
2-sided coated paper 3 (164 to 220 g/m2), 24: 2-sided coated paper 4 (221 to 256 g/m2), 25: 2-
sided coated paper 5 (257 to 300 g/m2)
26: Tracing paper (64 to 99 g/m2), 27: Transparency (121 to 220 g/m2), 28: Envelope (75 to 105
g/m2), 29: Postcard (164 to 220 g/m2), 30: Label (118 to 185 g/m2), 31: Pre-punched paper (64
to 75 g/m2), 32: Bond paper (83 to 99 g/m2), 33: Not used
Default Value 1
Related Service Mode COPIER> ADJUST> HV-TR> TR-ENV10, TR-DUP10, TR-VL10, 2TR-OFF
Supplement/Memo Up to 16 combination patterns can be set in TR-VL1 to 16 (setting 1 to 16). When there is more
than one setting where all conditions (environment, paper type and color mode/feed side) are the
same, the setting with a smaller setting number is applied.
676