Siemens SINUMERIK 840D sl Turning Operating Manual page 16
Hide thumbs
Also See for SINUMERIK 840D sl Turning:
- Function manual (2184 pages) ,
- Programming manual (1334 pages) ,
- Commissioning manual (1102 pages)
Table of Contents
Advertisement
Table of contents
10.3.1
General information..............................................................................................................442
10.3.2
Representation of the contour..............................................................................................443
10.3.3
Creating a new contour ........................................................................................................444
10.3.4
Creating contour elements ...................................................................................................446
10.3.5
Entering the master dimension ............................................................................................452
10.3.6
Changing the contour...........................................................................................................453
10.3.7
Contour call (CYCLE62) - only for G code program.............................................................454
10.3.8
Stock removal (CYCLE952) .................................................................................................455
10.3.9
Stock removal rest (CYCLE952) ..........................................................................................465
10.3.10
Plunge-cutting (CYCLE952).................................................................................................467
10.3.11
Plunge-cutting rest (CYCLE952)..........................................................................................473
10.3.12
Plunge-turning (CYCLE952) ................................................................................................476
10.3.13
Plunge-turning rest (CYCLE952) .........................................................................................482
10.4
Milling ...................................................................................................................................485
10.4.1
Face milling (CYCLE61).......................................................................................................485
10.4.2
Rectangular pocket (POCKET3) ..........................................................................................488
10.4.3
Circular pocket (POCKET4) .................................................................................................498
10.4.4
Rectangular spigot (CYCLE76)............................................................................................507
10.4.5
Circular spigot (CYCLE77)...................................................................................................513
10.4.6
Multi-edge (CYCLE79) .........................................................................................................519
10.4.7
Longitudinal groove (SLOT1) ...............................................................................................524
10.4.8
Circumferential groove (SLOT2) ..........................................................................................533
10.4.9
Open groove (CYCLE899) ...................................................................................................541
10.4.10
Long hole (LONGHOLE) - only for G code program ............................................................551
10.4.11
Thread milling (CYCLE70) ...................................................................................................553
10.4.12
Engraving (CYCLE60)..........................................................................................................557
10.5
Contour milling .....................................................................................................................564
10.5.1
General information..............................................................................................................564
10.5.2
Representation of the contour..............................................................................................564
10.5.3
Creating a new contour ........................................................................................................565
10.5.4
Creating contour elements ...................................................................................................568
10.5.5
Changing the contour...........................................................................................................573
10.5.6
Contour call (CYCLE62) - only for G code program.............................................................574
10.5.7
Path milling (CYCLE72) .......................................................................................................575
10.5.8
Contour pocket/contour spigot (CYCLE63/64).....................................................................581
10.5.9
Predrilling contour pocket (CYCLE64) .................................................................................583
10.5.10
Milling contour pocket (CYCLE63) .......................................................................................587
10.5.11
Contour pocket residual material (CYCLE63, option) ..........................................................593
10.5.12
Milling contour spigot (CYCLE63) ........................................................................................596
10.5.13
Contour spigot residual material (CYCLE63, option) ...........................................................601
10.6
Further cycles and functions ................................................................................................605
10.6.1
Swiveling plane / aligning tool (CYCLE800).........................................................................605
10.6.2
Swiveling tool (CYCLE800)..................................................................................................612
10.6.2.1
Aligning turning tools - only for G code program (CYCLE800) ............................................612
10.6.2.2
Aligning milling tools - only for G code program (CYCLE800) .............................................615
10.6.2.3
Preloading milling tools - only for G code program (CYCLE800).........................................615
10.6.3
High-speed settings (CYCLE832) ........................................................................................617
10.6.3.1
Parameters...........................................................................................................................620
10.6.4
Subroutines ..........................................................................................................................621
10.6.5
Adapt to load (CYCLE782)...................................................................................................623
16
Operating Manual, 06/2019, A5E44903486B AB
Turning
Advertisement
Table of Contents
