Busch-Jaeger mini KNX 6131/20 series Technical Manual page 6

11.5 "Constant light controller" application ........................................................................................................... 96
11.5.1
11.5.2
11.5.3
11.5.4
11.5.5
11.5.6
11.5.7
11.5.8
11.5.9
11.5.10
11.5.11
11.5.12
11.5.13
11.5.14
11.5.15
11.5.16
11.5.17
11.5.18
11.5.19
11.5.20
11.5.21
11.5.22
11.5.23
11.5.24
11.5.25
11.5.26
11.5.27
11.5.28
11.5.29
11.5.30
11.5.31
11.5.32
11.5.33
11.5.34
11.5.35
11.5.36
11.5.37
11.5.38
11.5.39
11.5.40
11.5.41
11.5.42
11.5.43
11.5.44
11.5.45
11.5.46
11.5.47
KNX Technical Manual 2CKA001473B8667 │ 06.02.2017
General parameters - Output is of type ..................................................................................................... 96
General parameters - Bottom limit output 1 (%) ........................................................................................ 96
General parameters - Upper limit output 1 (%) ......................................................................................... 96
General parameters - Control starts at (%) ............................................................................................... 96
General parameters - Control speed (mm:ss) ........................................................................................... 96
General parameters - Setpoint brightness (lux) ....................................................................................... 97
General parameters - Hysteresis (%) ........................................................................................................ 97
General parameters - Switch-off delay (hh:mm:ss) ................................................................................... 97
General parameters - Value for switch-off (%) .......................................................................................... 98
General parameters - Sensitivity of the watchdog .................................................................................... 98
General parameters - Fade in extended parameters ................................................................................ 98
Extended parameters - Operating mode ................................................................................................... 99
Extended parameters - Use of a two-stage switch-off .............................................................................. 99
Extended parameters - Value for reduced brightness (%) ...................................................................... 100
Extended parameters - Brightness reduced according to switch-off delay (hh:mm:ss) .......................... 100
Extended parameters - Slave sent .......................................................................................................... 100
Extended parameters - Used brightness ................................................................................................. 101
Extended parameters - Dimming step size brighter (1 to 15) .................................................................. 101
Extended parameters - Dimming step size darker (1 to 15) .................................................................... 101
Extended parameters - Use of output 2 .................................................................................................. 101
Extended parameters - Bottom limit output 2 (%) ................................................................................... 102
Extended parameters - Upper limit output 2 (%) ..................................................................................... 102
Extended parameters - Proportionality factor output 2 to output 1 (%) ................................................... 102
Extended parameters - Use of object for switch-off delay ....................................................................... 102
Extended parameters - Use of object for setpoint brightness ................................................................. 103
Extended parameters - Use of object for saving setpoint brightness ...................................................... 103
Extended parameters - Use of actual brightness object ......................................................................... 103
Extended parameters - Cyclic sending of actual brightness ................................................................... 103
Extended parameters - Sending of actual brightness every (hh:mm:ss) ................................................ 104
Extended parameters - Use of brightness calibration object ................................................................... 104
Extended parameters - Control speed adjustment through blind inputs ................................................. 104
Extended parameters - Total movement time of blind / roller blind (hh:mm:ss) ...................................... 104
Extended parameters - Dimming step size brighter (1 to 15) .................................................................. 104
Extended parameters - Dimming step size darker (1 to 15) .................................................................... 105
Extended parameters - Control speed (mm:ss) ...................................................................................... 105
Extended parameters - Actual brightness filter ....................................................................................... 105
Extended parameters - Exiting manual off dimming mode after (hh:mm) ............................................... 105
Extended parameters - Exiting manual off mode after (hh:mm) ............................................................. 105
Extended parameters - Pause time (ss.fff) .............................................................................................. 106
Extended parameters - Use of status of control object ........................................................................... 106
Extended parameters - Overwriting settings during a download ............................................................. 106
Sensor selection - Use of sensors 1 - 4 .................................................................................................. 107
Enable - Presence detector enable object .............................................................................................. 107
Enable - Enable with................................................................................................................................ 107
Enable - After bus voltage recovery, presence detector is ...................................................................... 107
Enable - At enable, output sends ............................................................................................................ 108
Enable - Output sends at blockage ......................................................................................................... 108
Table of contents
│6