Siemens SINUMERIK 808D ADVANCED Parameter Manual page 44

Machine data
3.2 General machine data
SD43230 $SA_SPIND_MAX_VELO_LIMS
SD43235 $SA_SPIND_USER_VELO_LIMIT
SD43300 $SA_ASSIGN_FEED_PER_REV_SOURCE
SD43350 $SA_AA_OFF_LIMIT
SD43420 $SA_WORKAREA_LIMIT_PLUS
SD43430 $SA_WORKAREA_LIMIT_MINUS
SD43600 $SA_IPOBRAKE_BLOCK_EXCHANGE
SD43610 $SA_ADISPOSA_VALUE
SD43700 $SA_OSCILL_REVERSE_POS1
SD43710 $SA_OSCILL_REVERSE_POS2
SD43720 $SA_OSCILL_DWELL_TIME1
SD43730 $SA_OSCILL_DWELL_TIME2
SD43740 $SA_OSCILL_VELO
SD43750 $SA_OSCILL_NUM_SPARK_CYCLES
SD43760 $SA_OSCILL_END_POS
SD43770 $SA_OSCILL_CTRL_MASK
SD43780 $SA_OSCILL_IS_ACTIVE
SD43790 $SA_OSCILL_START_POS
10710 PROG_SD_RESET_SAVE_TAB
- Setting data to be updated
-
- 30
Description:
Setting data to be backed up
The values of the SDs listed in this table are stored in non-volatile memory, i.e. they
remain valid after power ON. The setting data whose HMI numbers were entered in the
backup list are written into the (buffered) active file system after the description
of the part program on reset.
Programmable setting data are:
SD 42000
SD 42010:
SD 42400
SD 42800
SD 43200:
SD 43202:
SD 43210
SD 43220
SD 43230
SD 43300
SD 43420
SD 43430
SD 43700
SD 43710
SD 43720
SD 43730
SD 43740
SD 43750
SD 43760
44
0, 0, 0, 0, 0, 0, 0, 0...
$SC_THREAD_START_ANGLE
$SC_THREAD_RAMP_DISP
$SC_PUNCH_DWELLTIME
$SC_SPIND_ASSIGN_TAB
$SA_SPIND_S
$SA_SPIND_CONSTCUT_S
$SA_SPIND_MIN_VELO_G25
$SA_SPIND_MAX_VELO_G26
$SA_SPIND_MAX_VELO_LIMS
$SA_ASSIGN_FEED_PER_REV_SOURCE
$SA_WORKAREA_LIMIT_PLUS
$SA_WORKAREA_LIMIT_MINUS
$SA_OSCILL_REVERSE_POS1
$SA_OSCILL_REVERSE_POS2
$SA_OSCILL_DWELL_TIME1
$SA_OSCILL_DWELL_TIME2
$SA_OSCILL_VELO
$SA_OSCILL_NUM_SPARK_CYCLES
$SA_OSCILL_END_POS
LIMS
FPRAON
G26
G25
OSP1
OSP2
OST1
OST2
FA
OSNSC
OSE
OSCTRL
OS
EXP, N01
DWORD
- -
(GCODE)
SF
DITS/DITE
PDELAYON
SETMS
S with G94,G95,G97,G971,G972
S with G96,G961,G962
G25S
G26 S
LIMS
FPRAON
G26
G25
OSP1
OSP2
OST1
OST2
FA
OSNSC
OSE
Parameter Manual, 08/2015, 6FC5397-8EP40-0BA1
A3, V1
PowerOn
2/2
Parameter Manual