Siemens SINUMERIK 808D ADVANCED Parameter Manual page 286

Machine data
3.4 Axis-specific machine data
36060 STANDSTILL_VELO_TOL
mm/min, rev/min Threshold velocity/speed 'Axis/spindle in stop'
-
808d-me42 -
808d-me62 -
808d-te42 -
808d-te62 -
808d-mte40 -
808d-mte60 -
Description:
This MD defines the standstill range for the axis velocity / spindle speed. If the
current actual velocity of the axis or the actual speed of the spindle is less than
the value entered in this MD, the NC/PLC interface signal DB390x DBX1.4 (Axis/spindle
stationary) is set.
To bring the axis/spindle to a standstill under control, the pulse enable should not
be removed until the axis/spindle is at a standstill. Otherwise the axis will coast
down.
Related to:
NC/PLC interface signal DB390x DBX1.4 (Axis/spindle stationary)
36100 POS_LIMIT_MINUS
mm, degrees 1st software limit switch minus
CTEQ
- -
Description:
Same meaning as 1st software limit switch plus, however the traversing range
limitation is in the negative direction.
The MD becomes active after reference point approach if the NC/PLC interface signal
DB380x DBX1000.2 (2nd software limit switch minus) is not set.
MD irrelevant:
if axis is not referenced.
Related to:
NC/PLC interface signal DB380x DBX1000.2 (2nd software limit switch minus)
36110 POS_LIMIT_PLUS
mm, degrees 1st software limit switch plus
CTEQ
- -
Description:
A software limit switch can be activated in addition to the hardware limit switch. The
absolute position in the machine axis system of the positive range limit of each axis
is entered.
The MD is active after reference point approach if NC/PLC interface signal DB380x
DBX1000.3 (2nd software limit switch plus) has not been set.
MD irrelevant:
if axis is not referenced.
286
5.00, 5.00, 5.00, (0./ 0.)
1800.00
5.00, 5.00, 5.00, (0./ 0.)
1800.00, 360.00
5.00, 5.00, 5.00, (0./ 0.)
1800.00
5.00, 5.00, 5.00, (0./ 0.)
1800.00, 360.00,
360.00
(5.0/ 1.0), (5.0/ 1.0), (0./ 0.)
(5.0/ 1.0), (5.0/ 1.0),
(5.0/ 1.0), (5.0...
(5.0/ 1.0), (5.0/ 1.0), (0./ 0.)
(5.0/ 1.0), (5.0/ 1.0),
(5.0/ 1.0), (5.0...
-1.0e8 -
1.0e8 -
A05, A04 TE1, A2, A3, D1, Z1
DOUBLE NEW CONF
(1.e300/ 1.e300) 2/2
(1.e300/ 1.e300) 2/2
(1.e300/ 1.e300) 2/2
(1.e300/ 1.e300) 2/2
(1.e300/ 1.e300) 2/2
(1.e300/ 1.e300) 2/2
A03, A05, A11 TE1, R2, T1, A3, Z1
DOUBLE NEW CONF
- 2/2
A03, A05, A11 TE1, R2, T1, G2, A3, Z1
DOUBLE NEW CONF
- 2/2
Parameter Manual, 08/2015, 6FC5397-8EP40-0BA1
Parameter Manual