Engine Service Mode; Sp1-Xxx (Feed) - Ricoh G104 Service Manual

SERVICE MODE TABLE

5.2.3 ENGINE SERVICE MODE

SP1-XXX (Feed)

[Lead Edge Reg.] Leading Edge Registration
(Tray or By-pass, Paper Type, Process Speed)
Paper Type ->N: Plain paper 1, N2 or Normal 2: Plain paper 2, Thick2: Thick
paper 2 (see the Specifications table for details on these paper weights)
Process Speed: LS: Low speed, RS: Regular speed
Adjusts the leading edge registration. This SP changes the registration clutch
1001
operation timing for each mode.
+value sets the registration start timing earlier.
-value sets the registration start timing later.
NOTE: The value of the normal paper in RS is the standard value. The values
1001 001 Tray 1: Normal: LS
1001 002 Tray 1: Normal: RS
1001 003 Tray 1: Thick
1001 004 Tray 1: OHP
1001 005 Tray 2: Normal: LS
1001 006 Tray 2: Normal: RS
1001 007 Tray 2: Thick
1001 008 Tray 2: OHP
1001 009 Tray 3: Normal: LS
1001 010 Tray 3: Normal: RS
1001 011 Tray 3: Thick
1001 012 Tray 3: OHP
1001 013 By-pass: N: LS
1001 014 By-pass: N: RS
1001 015 By-pass: Thick
1001 016 By-pass: OHP
1001 017 Duplex: Normal: LS
1001 018 Duplex: Normal: RS
1001 019 Duplex: Thick
1001 020 Duplex: N2: LS
1001 021 Duplex: N2: RS
1001 022 Tray 1: Normal 2: LS
1001 023 Tray 1: Normal 2: RS
1001 024 Tray 1: Thick 2
1001 025 Tray 1: Thin: LS
1001 026 Tray 1: Thin: RS
1001 027 Tray 1: Special
1001 028 Tray 2: Normal 2: LS
1001 029 Tray 2: Normal 2: RS
1001 030 Tray 2: Thick 2
1001 031 Tray 2: Thin: LS
1001 032 Tray 2: Thin: RS
1001 033 Tray 2: Special
1001 034 Tray 3: Normal 2: LS
1001 035 Tray 3: Normal 2: RS
G104
CÓPIA NÃO CONTROLADA
of papers other than normal are added to the value of the normal paper
in RS.
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
*EGB
CÓPIA NÃO CONTROLADA
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
[-10.0 to 10.0 / -3.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.5 / 0.1 mm/step]
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
[-10.0 to 10.0 / -3.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.5 / 0.1 mm/step]
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
[-10.0 to 10.0 / -3.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.5 / 0.1 mm/step]
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
[-10.0 to 10.0 / -3.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.5 / 0.1 mm/step]
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
[-10.0 to 10.0 / -3.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.5 / 0.1 mm/step]
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.5 / 0.1 mm/step]
[-10.0 to 10.0 / 1.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.5 / 0.1 mm/step]
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.5 / 0.1 mm/step]
[-10.0 to 10.0 / 1.0 / 0.1 mm/step]
[-10.0 to 10.0 / 1.0 / 0.1 mm/step]
5-10 SM