Ricoh G104 Service Manual page 131

1004 079 DEV / OPC [K]: LS:
OHP
1004 080 DEV [CMY]: LS: OHP
1004 081 OPC [CMY]: LS: OHP
1004 082 Fusing: LS: OHP
1004 083 T.Belt: LS: OHP
1004 084 PFU: LS: OHP
1004 085 Duplex: LS: OHP
1006 [Phase Adjust.] Phase Adjustment
1006 001 Angle
1104 [Fusing Cont.] Fusing Control
1104 001 Control Method
Selects the fusing control method.
0: ON/OFF Control 1: PID Control (Phase control)
1104 022 Max. Wait Time
Adjusts the maximum waiting time for the target printing temperature of fusing
unit. After this interval, printing will start if the temperature did not get to the
target.
1104 023 Paper Feed. Temp.
Adjusts the increase in the temperature of the fusing unit between the ready
condition and the start of paper feed at the start of a new job.
1104 024 1st Add Time: LS
For print jobs at low speed. If the interval between jobs is less than this setting,
then the temperature change (1104 025) for the first page of a new job is not
applied.
1104 025 1st Add Temp.
Adds this value to the basic fusing temperature, for the first page of a new job.
This extra temperature is necessary because when the printer starts the first
page, the fusing unit is not warm enough.
1104 026 1st Temp. Maint.
Adjusts the time for maintaining the temperature change that is set with 1104
025.
1104 027 1st Print Inter.
For print jobs at regular speed. If the interval between jobs is less than this
setting, then the temperature change (1104 025) for the first page of a new job
is not applied.
SM
CÓPIA NÃO CONTROLADA
*EGB Adjusts the black development and OPC
motor speed.
[-4.00 to 4.00 / -1.35 / 0.01 %/step]
*EGB Adjusts the color development motor speed.
[-4.00 to 4.00 / 0.0 / 0.01%/step]
*EGB Adjusts the color OPC motor speed.
[-4.00 to 4.00 / -1.35 / 0.01%/step]
*EGB Adjusts the paper exit and fusing motor
speed.
[-4.00 to 4.00 / 0.6 / 0.01%/step]
*EGB Adjusts the transfer belt motor speed.
[-4.00 to 4.00 / 0.0 / 0.01%/step]
*EGB Adjusts the speed of the feed motor in the
optional paper tray unit.
[-4.00 to 4.00 / -1.14 / 0.01%/step]
*EGB Adjusts the duplex motor speed.
[-4.00 to 4.00 / -0.36 / 0.01%/step]
*EGB Adjusts the phase angle between the K drum
and the CMY drums.
[-180 to 180 / 0 / 1°/step]
*EGB [0 or 1 / 1 / -] Alphanumeric
*EGB [0 to 255 / 30 / 1 sec/step]
*EGB
[0 to 30 / 5 / 1°/step]
[0 to 50 / 0 / 0.1 sec/step]
*EGB
[0 to 20 / 0 / 1°C/step]
*EGB [0 to 50 / 0 / 1 sec/step]
*EGB [0 to 100 / 0.2 / 0.1 sec/step]
5-15
CÓPIA NÃO CONTROLADA
SERVICE MODE TABLE
DFU
G104