Toshiba Strata DK 280 Installation Manual page 412

table may be documented on the LCR Plan record
sheet:
Check the box on the record sheet next to Office
Code Exception Table number.
Enter the number of the exception table (01 - 16).
Make sure this table number is not entered on any
other plan, or on the continuation sheet.
Enter the applicable area code.
Enter the specific office codes that are to be
routed differently than the area code.
Program 53-LCR Schedule Assignments for LCR
Plans
This program assigns up to three time schedules to
each plan. Each time schedule consists of four or six
different route definition choices (defined in Program
54) available to the eight station groups (defined in
Program 56) (see Program 53 record sheet notes). It
may be helpful to complete Program 54 portions of the
plans and Program 56 before proceeding.
Typical Installation Without Time Scheduling
Feature
In most cases, an installation will not require use of
the time schedule feature. To reflect this on the record
sheets for Plans 01 - 16:
1. Enter the same Schedule Start Times for
Schedules 1 and 2. Use military time, in the format
HH:MM (Hours:Minutes). Fill in all four digits.
Initialized data assigns "0000" to all times.
+ If LCR software sees Schedules 1 and 2 have
the same start times, then it only looks at
Schedule 1 for route definitions.
2. Enter Route Definition numbers for Schedules 1
and 2. Four definitions (route choices) can be
entered for each group with RCTUA,
RCTUBNBB, RCTUB. or RCTUC/D.
+ LCR Station (Class) Groups 1 - 8 are
assigned in Program 56.
+ LCR Route Definition numbers l- 6 are
defined in Program 54.
+ The order in which the route definitions are
entered defines the order of LCR line
selection. The most desirable route should be
entered in the left-most position, and the least
desirable route in the right-most position.
+ If "1" is assigned to Station Group 1, and 1 for
route definition only, then those assigned will
only be able to use Route Definition 4, thereby
restricting them during times that route
definition 1 is not allowed.
+ Keep in mind that the route definition number
is being entered, not the CO line group
number. The definitions are assigned in
Program 54.
Installation Requiring Time Scheduling Feature
When an installation requires the time scheduling
feature to be programmed, three "shifts" of route
definitions can be assigned per station group. To
reflect this on the record sheet, substitute Step 1 of
the procedure described for the typical customer with
the following:
l
Enter the Schedule Start Times for Schedules 1, 2
and 3. Use military time, in the format HH:MM
(Hours:Minutes). Fill in all four digits. Initialized
data assigns "0000" to all times.
+ Start time for schedule 2 is the stop time for
schedule 1.
+ Start time for schedule 3 is the stop time for
schedule 2.
+ Start time for schedule 1 is the stop time for
schedule 3.
Program 54-LCR Route Definition Tables
The purpose of this program is to define four (RCTUA,
RCTUBNBB, or RCTUB) or six (RCTUC/D) different
ways of routing calls for each of the LCR plans (see
Program 54 record sheet notes). Define each route by
selecting and entering:
1.
CO Line Group (01 - 16): Refer to the LCR Line
Programming Reference Table completed at the
beginning of the LCR record sheets.
+ Each line group represents a type of service,
e.g.,
special common carrier, foreign
exchange, local line group, etc.
4 Program 16 assigns lines to groups 1 - 16
(801 - 816).
+ Program 40 denies incoming and outgoing
line access to stations, including LCR access.
+ Program 41 allows line access to stations
using LCR only for outgoing calls when
enabled.
.
9-52
January 1996