Nht/Nhr Options With Piou, Pious, Or Pepu; Ddcb And Hdcb/Drlk Assignments Guide - Toshiba Strata DK 280 Installation Manual

10. Check each door lock button from each station:
The HDCB modular B-jack (pins 3 and 4) will
momentarily close (three or six seconds) when the
appropriate door lock button is pressed.
Note:
The HDCB W2 strap is not used with Strata
DK280 systems. The strap provides an alarm
function with other Strata systems.
6.3.2 DDCB
and
HDCB/DRLK Assignments
Guide
Table
6-1
DDCB and HDCB/DRLK Assignments Guide
DDCB/
RDSWPDKW
Port HDCB Program 39 Button
PEKWPESU No. No.
Assignments
First (fifth circuit,
004 1 Unlock Door 1
slot 11)
(DRLK I), Code 72
Second (fifth circuit, 012 2
Unlock Door 2
slot 12)
(DRLK 2), Code 73
Third (fifth circuit,
020 3 Unlock Door 3
slot 13)
(DRLK 3), Code 74
Fourth (fifth circuit,
028 4
Unlock Door 4
slot 14)
(DRLK 4), Code 7.5
DK031
Notes:
1. See Programs 39, 77-1, and 77-2 to
program assignments.
2. DDCB and HDCB hardware option
settings for door lock control operation:
n Set SW1 ('jumper) to DOOR position.
n Set SW2 (switch) to LOCK position.
6.3.3 NHT/NHR Options with PIOU,
PIOUS, or PEPU
The NHT/NHR may be programmed for either the
Night Relay or the MOH relay function. (Refer to
Figures 6-7 and 6-8.)
Note:
Only the PIOU/PIOUS, or PEPU with the
lowest Program 03 code (4 1, 42 or 43) will
provide the NT or MOH relay control function.
When configured for the NT function with
Program 77-1, the relay activates if the system is in
the NIGHT mode. The relay may be programmed to
activate continuously when the Night Transfer button
(only) is set for the NIGHT mode (for indirect
answering machine control), or to pulsate at one-
second ON/three-seconds OFF (for a night bell) when
incoming CO lines ring (NT1 = tenant 1 CO lines -
NT4 = tenant 4 CO lines) per Program *15 and 77-3.
When configured for the MOH function with Program
77-1, the relay activates any time a CO line is on hold.
In this configuration, the relay is normally used to
control the MOH source.
NHT Control
Configure the PIOU, PIOUS, or PEPU for the NHT
function in accordance with the following steps (refer
to Figures 6-7 and 6-8):
1.
2.
3.
4.
5.
6.
7.
Access Program 77-l. Set LED 05 to OFF to
configure the Night/Hold Relay for the NHT
function.
Access Program 77-l. Set LED 06 to provide
continuous or pulsating relay activation as follows:
4 OFF-Programs the relay for continuous
activation when the Night Transfer (NT)
button (only) is set in the NIGHT mode.
n ON-Programs the relay for pulsating
activation when the Night Transfer (NT)
button for tenant 1 - 4 is set to the NIGHT
mode and a CO line rings.
Note:
CO lines must be enabled in Program 78 for
the NT pulsating relay function.
Access Programs 87, 88, and 89 to set the CO
lines that will activate the relay (when the system
is in the NIGHT mode).
Access Program 39 to assign Night Transfer (NT)
buttons to telephones that should be able to set
the Strata DK280 system into the NIGHT mode.
Access Programs 29-l - 29-4 to program a Night
Transfer button on all direct station selection
consoles that are to transfer the Strata DK280
system into the NIGHT mode.
If tenant operation is required, access Program
*I5 to set the CO lines for tenant 1 - tenant 4
operation. RCTUA and RCTUB provides two
tenant assignments, RCTUCYD provides four.
If using a PIOU or PEPU, set the Pi 1 jumper plug
on the PIOU or PEPU to the MAKE or BREAK . . .
position, as required:
..:
,
6-14
January 1996