Smdr Printer/Call Accounting Device Installation; Voice Mail Options; System Hardware Requirements; Toshiba Vp Voice Messaging System - Toshiba Strata DK 280 Installation Manual

Program 03
n The SMDR output will be provided by the PIOU or
PIOUS with the lowest code assigned (41, 42, or
43).
H If using RSIU or RSIS PCB in slot 11 for SMDR,
set Program 03 code 49 for slot 11.
Note:
RSIWRSIS Program 76-1 code x2 will
override PlOWPIOUS SMDR assignments
and code 49 for RSWRSIS.
Program 60
n Item l-Selects Caller ID, ANI and DNIS or
Account Code to be sent out the SMDR Port.
n Item 2-Selects the minimum duration (1 .O or 10
seconds) of calls that will be registered by SMDR .
Any call that lasts less than the set time will not be
recorded.
n Item 3-Selects the records of outgoing calls or
outgoing and incoming calls to be printed.
n Item 4-Selects the digit length of Account Codes
(4 to 15 digits).
n Item 5-Allows only long distance call records to
be printed.
H Item 6-DISA security code.
4 Item 7-Credit card calling digit length.
Program
76-If RSIU or RSIS is used to interface to
the SMDR device use Program 76 to make the
appropriate RSIU/RSIS SMDR programming
assignments.
Program
97-Allows system program data to be
printed via the SMDR port (See Program 97 record
sheet and Figure 6-22).
Notes:
1. An SMDR printer must be connected to
the SMDR port to use the printout option
selected by Program 97.
2. Call record data is lost when program
data is printed out using Program 97.
6.7.2 SMDR Printer/Call Accounting Device
Installation
Install the SMDR printer/call accounting device option
in accordance with the following steps: (Refer to
Figure 6-23 and related drawings in Chapter 7-
Wiring Diagrams.)
1.
2.
3.
4.
Connect the interface cable and the PPTC or
PPTCS adapter from the PIOU, PIOUS, RSIU, or
RSIS SMDR port to the SMDR printer or call
accounting device DB2.5 or DB9 connector.
Set the PIOU or PIOUS SW1 switch to the
appropriate bps rate (300 or 1200 bps), as
determined by the baud rate of the printer or call
accounting device (Program 76 set RSIU/RSIS
bps rate).
Set the printer or call accounting device to
8-bits/no parity/one stop bit.
Use Program 60 to set the system for the required
SMDR printer/call accounting device options (refer
to Subsection 6.7.1, paragraph 3 and the
Programming Part).
6.8 Voice Mail Options
6.8.1 System Hardware Requirements
Strata DK280 systems can support a Toshiba VP or
Stratagy voice mail messaging system or a customer-
supplied voice mail system.
Voice mail systems connect to standard telephone
circuits (RSTU, RSTU2, RDSU/RSTS, PSTU or
PESU). The number of circuits required by each
device depends on the customer's voice mail
requirements, such as the number of voice mail users.
The RCTU must be equipped with a RRCS to support
voice mail.
Voice mail integration is provided by Strata in-band
tones and/or the Simplified Message Desk Interface
(SMDI) output of the PIOU, PIOUS, RSSU, RSIU, or
RSIS SMDI port. The PIOU/PIOUS/RSSU must be set
with Program 03, code 43 or for RSIU/RSIS Program
03, code 49 and Program 76-1 must be set with code
x4 to provide SMDI output. See the SMDI section for
more details about SMDI installation and operation.
6.8.2 Toshiba VP Voice Messaging System
Strata DK280 systems are designed to support the full
range of features offered by the Toshiba VP and/or
Stratagy. It provides various call routing, message
handling, and information management features,
including:
I
n Auto Attendant
January 1996
6-33