Toshiba Strata DK 280 Installation Manual page 398

one [DN] - that [DN] button can be assigned to appear
and ring on up to 120 telephones.
Program 80-Electronic and Digital Telephone
Ringing Tones
Distinctive system ringing sends a different ring tone
for CO (loop, ground or DID) line ringing than that for
Directory Number, intercom, or tie line ringing. In
addition, CO line (loop, ground or DID) ringing at
electronic and digital telephones can be different from
one phone to another. "Ring-transfer" ring tone pitch
(frequency) is also changed with this assignment.
Three choices are available with Program 80; see the
record sheet for the tone frequencies available with
each choice.
Programs 81 - 89--Ground/Loop Start/CO
Line/Station Auto Attendant, Attendant Console,
and Distributed Hunt Group Ringing Assignments
These programs assign CO lines to ring station [PDN]
ports and/or Distributed Hunt group port reference
numbers (900 - 915). A wide variety of line ringing to
stations can be programmed into the system. There
are nine categories: Day Immediate, Day Delay1 , Day
Delay2, Day2 Immediate, Day2 Delayl, Day2 Delay2,
Night Immediate, Night Delay1 and Night Delay2. Day,
Day2 and Night refer to the Night Transfer
button's three modes. Delay1 is a 12-second delay of
ringing signal to a standard, electronic, or digital
telephone; Delay2 is a 24-second ring delay. The
delay functions are mainly used in Centrex
applications but can be used for other situations. If
delayed ringing occurs, the station that initially rings
will continue to ring with subsequent delayed ring
stations. Initialized data reads all LEDs ON for Port
000 in Program 81 and Port 001 in Program 87; all
other LEDs are OFF.
A maximum of 120 telephones per CO line can be
assigned to ring simultaneously in any combination of
each of the Day, Day2 or Night ringing assignments.
In Release 3, Program 81 - 89 only assigns
telephones or a Distributed Hunt group to each CO
line that will ring. Program *81, *84, and *87 must be
used to assign which
[DN], [PDN], [SDN],
or
[PhDN]
should flash when the telephone rings but Program
*81, *84, and *87 data should be blank for CO lines
that ring VM ports.
q
Built-in Auto Attendant (AA)-Delay Answer
Ringing
Option-can be programmed to answer
incoming calls on a delayed ringing basis in either
the Day, Day2, or Night mode.
For example, to have a line answered by the
AA
on a Delay1 or Delay2 basis during the Day mode,
first assign the line for the AA feature in-Program
78-61.
To have the line answered by AA on a Delay1
basis, assign the station ports that must
immediately ring with Program 81. Also, assign
the [PDN] or [PhDN] that must flash in Program
*81. Next, assign the line to ring any other station
port with Program 82. To have the line answered
by AA on a Delay2 basis, assign the station ports
that must immediately ring with Programs 81 and
stations that should ring 12 seconds after the
Immediate ring stations with Program. Then
assign any other station port with Program 83. The
stations assigned to delay ring in Program 82
must also be equipped with the [DN] button that is
assigned to flash in Program *81 (see Program 81
- 89 record sheet notes).
n
Attendant Console Load Sharing Option-
Assign all CO lines (Loop, Ground and DID) that
should alternately ring between multiple attendant
consoles to ring the respective console ports in
Program 81, 84 and 87 (see Chapter 5-Station
Apparatus, sub-section 5.7.2).
Program *81, *84, and *87 - Ground/Loop Start/
CO line to [DN] Button LED Flash Assignments
Ground/loop start CO lines can be assigned to ring
and flash Directory Numbers ([PDNs]/[SDNs] or
[PhDNs]). This program assigns which [DN] will flash
when a ground/loop start CO line rings direct incoming
to the DK280 system. Program 81-89 must be used (in
conjunction with Program *81/*84/*87) to ring the
telephone on which the flashing [DN] appears. Each
ground/loop start CO line can be assigned to flash one
[DN] ([PDN]/[SDN] or [PhDN]) that [DN] button can
be assigned to appear and ring on up to 120
telephones.
II Program *81 is used to assign which [DN] will
flash when the CO line rings during the system
Day mode.
q Program *84 is used to assign which [DN] will
flash when the CO line rings during the system
Day2 mode.
n Program *87 is used to assign which
[DN]
will
flash when the CO line rings during the system
.
Night mode.
I
9-38
January 1996