Toshiba Strata DK 280 Installation Manual page 369

Speed Dial Memory. The three-minute setting is
recommended if station users frequently store
memos with Speed Dial numbers using the MODE
button below the Liquid Crystal Display (LCD).
q
Built-in Auto Attendant Camp-on Busy/Ring No
Answer Routing, LED 18 is designed for Auto
Attendant configurations that have primary
announcement devices, but no secondary ones-
tells the system where to route Auto Attendant
calls that ring and are not answered or have been
camped-on for a designated time (see Program
26). The calls can be sent back to the primary
announcement device or to the station or stations
assigned to the CO lines' normal ringing pattern
(see Programs 81, 84, and 87).
q
Built-in Auto Attendant Disconnect Time, LEDs
16 and 17-If LED 18 is assigned for normal
ringing, set LEDs 16 and 17 to tell the system
when to disconnect Built-in Auto Attendant calls
that have not been answered by the alternative
stations. This feature assures that the loop start
CO line that the call was made on will be free for
other calls if the caller hangs up before answered.
The initialized disconnect setting is 40 seconds.
The other timing options available are 150
seconds and 350 seconds. Set LEDs 16 and 17
for the desired time as follows:
+ 40 seconds: LED 16 = Off. LED 17 = Off.
+ 120 seconds: LED 16 = Off. LED 17 = On.
+ 240 seconds: LED 16 = On. LED 17 = Off.
W Built-in Auto Attendant MOH/RBT for Transfer,
LED 15-Callers can hear ring back tone (RBT) or
Music-on-hold (MOH) after being transferred from
the Built-in Auto Attendant to a station, depending
on the selection made with LED 15.
H RS-232 Voice Mail Signaling Method (LED
14)-The DK280 provides two types of RS-232
signaling: Bellcore Standard type (TR-TSY-
000283, TR-NWT-000283) or Toshiba Proprietary.
Refer to the VM machine installation
documentation and contact the Toshiba and/or VM
machine manufacturer for VM machine SMDI
configuration.
Notes:
1. Toshiba VP products require Release 7
software or above for
Toshiba
proprietary
integration.
2. Toshiba VP products require the "SW-
X0042 feature package (C. 0. Centrex) for
SMDI, but not for Toshiba Proprietary RS-
232 Interface.
3. Toshiba Stratagy products support SMDI
only in the standard configuration, not
Toshiba proprietary RS-232 interface.
q
SMDI Station Number Digit Length (LED 13-
lo)--This refers to the station digit length that the
SMDI voice mail system design requires. This
parameter is set for the Voice Mail system digit
length; not the DK280 station digit length. If the
voice mail system SMDI is designed per the
Bellcore Standard TR-TSY-000283, 1985 version,
set this parameter to seven-digits (LEDs 10, 11,
and 12 "On" which is equal to Hex 7). Current VP
and Stratagy voice mail SMDI systems are
designed for this seven-digit operation. If the voice
mail system SMDI is designed per the Bellcore
Standard TR-NWT-000283, 1991 version, set this
parameter between l-10 dig+ with LEDs 10, 11,
12, and 13. (See Program 10-3 record sheet for
LED-HEX values.) Digit length setting is not
necessary with Toshiba Proprietary Interface (LED
lo-13 OFF).
n
(LED 08)-This option determines if Caller ID
(CLID) and/or Automatic Number Identification
(ANI) telephone numbers will be sent out the
system SMDI port (SMDI only not Toshiba
proprietary):
+ Turn LED 08, 10, 11, 12, and 13 "ON" if
received Caller ID and/or ANI numbers should
be sent out the system SMDI port. ,
+ Turn LED 08 "OFF" if received Caller ID
and/or ANI numbers should not be sent out
the system SMDI port.
+ The system will initialize with LED 08 "OFF" -
no CLID or ANI information will be sent out the
SMDI port.
n
SMDI Bellcore Standard Version (LED 09)-
Bellcore released two versions of the SMDI
specification. Contact your voice mail machine
vendor to determine which specification to enable
with this program - TR-TSY-000283,
Issue 1, July
1985 version, or the TR-NWT-000283, Issue 2,
May 1991 version. Toshiba VP and Stratagy SMDI
products currently use the 1985 version. In either
case, the VM station digit length must be set with
LED lo-13 as shown above. Also note that the
1985 and 1991 version Bellcore specifications use
different space/character parameters for some call
types which means the DK280 will not operate
January 1996
9-9