Toshiba Strata DK 280 Installation Manual page 388

,
Program *42-l, Primary Timing Reference
Assignment
Assign the Primary Timing Reference with this
program.
LCD telephones can be allocated memory to save up
to 100 numbers in 10 number increments. The total
memory allocated to all stations in a system is: RCTU
C3/D3 = 1000 numbers; RCTUBABI RCTUBBB = 400
numbers; RCTUA3 = 200 numbers.
Program *42-2, Secondary Timing (Backup)
Reference Assignment
Assign the Secondary (Backup) Timing Reference
with this program.
Note:
To assign RDTUs as the Master Clock
Reference (free run), leave Programs *42-l
and *42-2 blank. Press button/LED 01 to
enter blanks.
Programs 50 - 56-Least Cost Routing
All Least Cost Routing program information is
provided later in this chapter.
Program *50-Caller ID (RCIU/RCIS) Circuit
Assignments to CO Line (RCOU/RCOS/RGLU/
PCOU)
Each analog ground/loop start CO line that receives
Caller ID information from the local Central Office
must be assigned to an RCIU or RCIS circuit using
this Program. This is necessary to allow Caller ID
information to be recognized by the DK280 system
processor. Any RCIU or RCIS circuit can be assigned
to any analog ground/loop start CO line circuit.
Each RCIU slot will be allocated eight Caller ID circuits
when assigned with Code 81 in Program 03; because
of this, you should always install RCIS on RCIU when
more than four circuits are required.
Note:
The Tip/Ring leads of RGLU/RCOU/RCOS/
PCOU Caller ID CO lines assigned to
RCIlJ/RCIS circuits must be bridged at the
MDF. For more information on RCIWRCIS
assignments and Installation, refer to Chapter
4-Printed Circuit Boards and Chapter 7-
Wiring Diagrams in the Installation Part of this
manual.
Program *51-Station Memory Allocation to
Store Caller ID and/or ANI Numbers on
Abandoned/Unanswered Calls
Any LCD telephone that must store abandon call
information for Caller ID, Ground/Loop start lines
and/or ANI, DID/tie lines must be allocated "Abandon-
Call-Memory" using this Program.
1.
2.
3.
4.
IMPORTANT!
On direct incoming calls that ring on more
than one telephone, the Caller ID,
Ground/Loop start, line must also be
assigned to the designated abandon call
storage LCD telephone in Program 62 .
If a CO line only direct-rings one
telephone, that telephone will store the
abandoned call information automatically
without being assigned in Program *52;
however, Program 61 is still required.
On direct incoming calls, the ANI abandon
call information will 'be stored in the
"Abandon-Call-Memory" of the [PDN]
owner or [PhDN] owner LCD telephone -
depending on which [ON] rings when the
call is received. Do not assign ANYDNIS
lines in Program 62.
Abandoned ring-transferred calls will store
Caller ID and/or ANI information in the
"Abandon-Call-Memory" of the
"'transferred -to-station". The 'transferred-
to-station" does not have to be assigned
as owner of the CO line in Program 62
(Caller ID) or as the owner of the [PhDN]
in Program *33 (ANI), but it must be
assigned memory in this Program.
Abandoned "Call-forwarded" calls will
store Caller ID and/or ANI information in
the "Abandon-Call-Memory" of the "first-
call-forwarded-from-station". The "first-
call-forwarded-from-station" does not
have to be assigned as the owner of the
CO line in program 62 or as the owner
of the [PhDN] in Program *33, but it must
be assigned memory in this program.
Program *52 - Caller ID and/or ANI Line Circuit
Abandoned Call Number Store Station Owner
Assignments
When Caller ID and ANI lines ring into the DK280
system and the caller hangs-up before the call is
answered, the call is considered abandoned. In this
case, the Caller ID and ANI infprmation received.can
be stored at a designated LCD telephone. When a
Caller ID line rings at more than one telephone
(Program 81-89), the LCD telephone that should store
9-28
January 1996