Avaya PARTNER ACS Installation And Use Manual page 406

System Flow Chart–System
System Date
#101
Dial
Dial the date (MMDDYY)
System Day
2.0 or earlier
#102
Dial
Dial 1=Sun ✔
2=Mon 3-Tue, 4=Wed, 5=Thur, 6=Fri,
7=Sat
System Time
#103
Dial
Dial the time (HHMM-24 hr. military time)
Number of Lines
#104
Dial
Dial two digits (01-31) (R 4.0), or
Dial two digits (01-19) (Prior to R 4.0),
for # of outside lines assigned to every
extension. 3 per ACS processor &
308EC module. 2 per 206 or 200 module
✔. 4 per 400 module ✔
WARNING
Do not use Number of Lines (#104) after
initial setup. In Key mode, the Number of
lines procedure will change Line
Assignment (#301), Line Access
Restriction (#302), Automatic Line
Selection and Line Ringing to factory
settings
To change line assignments without
affecting other settings, use Line
Assignment (#301)
In Hybrid mode, the Number of Lines
procedure will change Pool Line
Assignment (#207), Pool Extension
Assignment (#314), and Pool Access
Restriction (#315). Additionally, it
changes Line Assignment (#301), Line
Access Restriction (#302), Automatic
Line Selection and Line Ringing. To
change pool assignments without
affecting other settings, use Pool Line
Assignment (#207) and Pool Extension
Assignment (#314)
Transfer Return Rings
#105
Dial
Dial 1 digit (0-9) for # of rings before call
returns.
0-9 rings
4 rings ✔
Recall Timer Durations
#107
Dial
Dial two digits (01-80) to set length of a
switchook flash ✔=18 (450 msec)
Rotary Dialing Timeout
#108
Dial
Dial 1=4 secs
2=8 secs ✔
3=12 secs
Outside Conference Denial
#109
Dial
Dial 1=Allowed ✔
2=Disallowed
Automatic System Answer Delay
#110
Dial
Dial a ring delay number (0-9)
2 rings ✔
Automatic System Answer
Button
#111
Dial
Dial 1=Assigned
2=Not Assigned ✔
3=Select Button then press a
programmable button
Direct Extension Dial Delay
#112
Dial
Dial a ring delay number (0-9),
2 rings ✔
0 rings=answered immediately
Direct Extension Dial Button
#113
Dial
Dial 1=Assigned,
2=Not Assigned ✔
3=Select Button then press a
programmable button
Outgoing Call Restriction
Button
#114
Dial
Dial 1=Assigned
2=Not Assigned ✔
3=Select Button then press a
programmable button
Wake Up Service Button
#115
Dial
Dial 1=Assigned
2=Not Assigned ✔
3=Select Button then press a
programmable button
Call Coverage Rings
#116
Dial
Dial 1-9
2 ✔
VMS Cover Rings
#117
Dial
Dial 1-9
3 ✔
Ring On Transfer
#119
Dial
Dial 1= Active ✔
2=Not Active
Automatic System Answer Mode
2.0
#121
Dial
Dial 1=Hold ✔
2=Disconnect
3=Ring
2.0
Caller ID Type
#122
Dial
Dial 1=USA ✔
2=Singapore
2.0
Backup Programming Automatic
#123
Dial
Dial 1=Active
2=Not Active ✔
3=Backup Alarm Cleared
2.0
Backup Programming–Manual
#124
Dial
e
Press to begin the backup
Restore Programming
#125
Dial
Dial 1= MAN.mmddyy ✔
2=AUTO.mmddyy
e
Press to begin the restore
Automatic Daylight/ Standard Times
#126
Dial
Dial 1=Active ✔
2=Not Active
Mode of Operation
f00s
Press
s#198
2.0 only
Enter the system password
Dial 1=Key (factory setting) ✔
2=Hybrid
System Reset–Programming
Saved
IMPORTANT: Using this procedure
disconnects any active calls but
retains system settings. Use it only if
the system fails to function correctly
after a power failure or down period.
#728
Dial
Flow Charts
3.0
E-2