1. Manuals
  2. Brands
  3. Christie Manuals
  4. Projector
  5. Matrix StIM-WQ
  6. User manual

Christie Matrix StIM-WQ User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Matrix StIM
™
WQ/SIM WQ
U s e r M a n u a l
020-100883-01

Advertisement

Table of Contents
loading

Related Manuals for Christie Matrix StIM-WQ

Summary of Contents for Christie Matrix StIM-WQ

  • Page 1 Matrix StIM ™ WQ/SIM WQ U s e r M a n u a l 020-100883-01...
  • Page 3 Matrix StIM ™ WQ/SIM WQ U S E R M A N U A L 020-100883-01...
  • Page 4 Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose.
  • Page 5 Addendum The CD included with this printed manual contains an electronic copy in English. Please read all instructions before using or servicing this product. 手册中包含 的光 盘，带有着中文的电 子 副本， 使用 或维 修本 产品 前 ， 请 仔 细 查 阅 所 有的指示。...

  • Page 7: Table Of Contents

    Safety Warnings and Cautions........1 Projector Overview .
  • Page 8 Boresight Alignment ..........22 Adjust Software to Optimize Image .
  • Page 9 Adjust InfraRGB Across the Array from the Master Projector ....43 Adjust InfraRGB to Individual Projectors ......43 Setup Source Sequence .
  • Page 10 Communications ..........61 Serial Options .
  • Page 11 Projector Numbers (optional) ........79 Function Code .
  • Page 12 Frame Lock Enable (FLE) ......... . . 97 Serial Flow Control (FLW) .

  • Page 13: Safety Warnings And Cautions

    Safety Warnings and Cautions Always power down and disconnect/disengage power before servicing or clean- ing. Failure to comply could result in death or serious injury. 013- 102318- 01 R EV 02 Risk Group 2: Possible hazardous optical radiation emitted from this product. Do not stare at operating lamp.

  • Page 14: Projector Overview

    Projector Overview Projector Overview ™ Matrix StIM /SIM WQ projectors are professional quality WQXGA data projectors featuring the latest ® in DLP display technology to achieve high brightness, high resolution video projection images. The modular design of the Matrix StIM™/SIM WQ projectors makes them an ideal choice for the demanding needs of simulation applications.

  • Page 15: List Of Components

    Contacts To assist with the servicing of your projector, fill out the following information and keep with your records. Purchase Record Dealer Dealer or Christie Sales / Service Contact Phone Number Serial Number Purchase Date Installation Date * The serial number can be found on the license label.

  • Page 17: Installation Considerations

    Installation Considerations This section explains how to install, connect and optimize the projector. Illustrations are graphical representations only and are provided to enhance the understanding of the written material. When designing a projection room for either a permanent or temporary installation, consider positioning the projector and screen for maximum audience coverage and space efficiency.

  • Page 18: Installation Procedures

    Do not place the projector onto a surface with the line cord retainer side down. Failure to comply may result in damage to the line cord retainer. Christie recommends that the packaging material for at least 1 projector is saved in case one needs to be shipped for service.

  • Page 19: Mount The Projector

    If you are mounting a ruggedized kit use the 7 designated mounting points on the front of the projector. The handles will need to be removed to access 4 of these points. Christie does not provide the ruggedized kit or the hardware to secure a ruggedized kit. Christie recommends using M6 hardware with a 10 mm thread engagement, and a maximum torque of 4 Nm.

  • Page 20: Install The Lens

    Installation Procedures Install the Lens Risk Group 2: Possible hazardous optical radiation emitted from this product. Do not stare at operating lamp. May be harmful to the eyes. Failure to comply è è C AU TI O N / R i sk G r oup 2/ q³I§...

  • Page 21: Setup Procedures

    Setup Procedures Setup Procedures Adjust Lens Focus Failure to properly adjust lens focus results in an image that is not uniformly focused and contains geometric distortion. This section describes best practices for lens focus adjustment of the 0.68:1 WQXGA lens  (P/N: 125-103105-xx), the 0.80:1 WQXGA lens (PN: 125-105107-xx), and the 1.28 - 1.71:1 WQXGA lens (P/N: 125-101103-xx).

  • Page 22: Calculate Throw Distance And Position

    Setup Procedures Calculate Throw Distance and Position Throw distance is the distance measured from your projector to the screen. This calculation determines if there is enough room to install your projector with a desired screen size and if the image size will be the accurate size for your screen. To estimate the throw distance take the horizontal width of the screen and multiply it by the lens throw ratio.

  • Page 23: Determine Vertical And Horizontal Position

    Setup Procedures Determine Vertical and Horizontal Position The projection lens and the screen type determine the vertical and horizontal position of your projector in relation to the screen. Ideally, you should position the projector perpendicular to the screen to make the image appear rectangular instead of keystoned (trapezoidal). You can offset vertical position of the image (move it above or below the optical axis) by adjusting the lens mount.

  • Page 24: Connect A Source

    Setup Procedures Connect a Source All source connections are made to the input panel, located at the back of the projector. Each input is labeled for easy identification. Using the correct cable(s), connect your source. See Network Setup for External Communications on page 15.

  • Page 25: Inputs 1 And 2

    Setup Procedures Inputs 1 and 2 Native WQ is required in order to receive a valid DVI-D signal. Use Inputs 1 and 2 to connect the main and secondary input sources. See Select Inputs on page 40. The LEDs assigned to each input indicate the following: S indicator (signal) F indicator (function) Green: Indicates valid DVI-D source...

  • Page 26: Connect To Power

    The dedicated earth wire must be installed by a Christie accredited service technician. To connect the projector to an IT power distribution system connect the building ground to the internal ground lug behind the AC input inside the projector.

  • Page 27: Network Setup For External Communications

    Setup Procedures Network Setup for External Communications To complete the projector network setup you will also need to connect the projectors together for ArrayLOC communication and functions. See ArrayLOC Network Configuration on page 19. Ethernet (recommended) In the Ethernet network the controller communicates with each projector separately. Recommended for network administrators only.

  • Page 28: Mixed Network

    Setup Procedures Mixed Network Using the wrong type of serial cable can damage the projector. RS-232 communication cables must be of good quality and no more than 25 ft (7.62 m) in length. Failure to comply may result in equipment damage. In a mixed network the controller can communicate with the first projector and the command can be relayed to each serially connected projector.

  • Page 29: Rs-232 Network

    Setup Procedures RS-232 Network Using the wrong type of serial cable can damage the projector. RS-232 communication cables must be of good quality and no more than 25 ft (7.62 m) in length. Failure to comply may result in equipment damage. In an RS-232 network the controller can communicate with the first projector and the command can be relayed to each serially connected projector.

  • Page 30: Mixed Serial Network (Rs-232 And Rs-422)

    Setup Procedures Mixed Serial Network (RS-232 and RS-422) Do not connect incompatible equipment, including the wrong type of serial cable to the  RS-422 port. Failure to comply could cause equipment damage. RS-422 serial communication is better over long distances than RS-232 communication. Use the  RS-422 port only if your device has RS-422 capability.

  • Page 31: Arrayloc Network Configuration

    Setup Procedures ArrayLOC Network Configuration Preliminary color setup is managed by ArrayLOC. ArrayLOC is enabled by default and configured to display a reasonably saturated gamut at the maximum brightness that all the projectors in the array can support. See Configure the Display on page 59 for detailed information.

  • Page 32: Arrayloc Over Arrayloc Network (Preferred)

    Setup Procedures ArrayLOC over ArrayLOC Network (preferred) The ArrayLOC Network should be used if you want to isolate the ArrayLoc network traffic from the Control Network. 1. Connect a standard CAT5 Ethernet cable between the ArrayLOC network switch and the ArayLOC Network port on the projectors input panel.

  • Page 33: Adjust Image Geometry And Optical Alignment

    In rear screen applications where space behind the projector is limited, a mirror may be used to fold the optical path. The position of the projector and mirror must be accurately set — if considering this type of installation contact Christie Customer Support for assistance. Matrix StIM™ WQ/SIM WQ User Manual...

  • Page 34: Boresight Alignment

    Setup Procedures Boresight Alignment • Boresight alignment is an advanced feature and should only be performed by experienced users. • You can also use the Grid or Edge blend test pattern to perform boresight alignment. 1. Display the Boresight test pattern by pressing Test on the IR remote and use the Left arrow key to cycle to Boresight.

  • Page 35: Adjust Software To Optimize Image

    Setup Procedures Adjust Software to Optimize Image Unless otherwise indicated, instructions apply to all projector models in stand-alone or multi-projector configurations. 1. Display an external signal. 2. Select Screen Image Orientation in Configuration > Output Options and change the orientation of the displayed image to suit the installation.

  • Page 37: Login To Webui

    Login to WebUI 1. Open your web browser and enter the IP address (in the address bar) assigned to your projector. The factory default IP address is 192.168.1.89. To change the default use the NET serial command through RS-232. See Network Setup (NET) on page 108.

  • Page 38: Navigate The Webui

    Navigate the WebUI Navigate the WebUI This section describes the controls and switches used for projector operation once it is properly installed and configured. The Matrix StIM™ WQ projector can be controlled remotely, typically at a controller such as a PC, via a WebUI on an Ethernet Network. If there are concerns about network security, run the WebUI on a local area network only and install a firewall.

  • Page 39: The Global Icon

    Navigate the WebUI The Global Icon Menu options that include this icon, apply globally. Menu options without this icon apply to the selected projector only. Slidebars in Menus The current value for a given parameter appears to the left of its slidebar icon.

  • Page 40: Help Text

    Navigate the WebUI Help Text Help text is not available for disabled buttons. You can move your mouse pointer over most buttons or fields to display related help information. When working with the projector menu system on the Tools tab, highlight the menu option and press h. To disable this feature, select the Admin tab and click on the Hide button underneath Tooltip.

  • Page 41: Basic Webui Operation

    Basic WebUI Operation Basic WebUI Operation Five primary tabs are located along the top of the WebUI. Each primary tab also has related secondary tabs, which are located along the bottom of each tab. Main Tab — General Under the Main tab, select the General tab at the bottom of the window to view general information on inputs and projector status, and to activate a test pattern and color enable control.

  • Page 42: Tools Tab - Virtual Osd

    Basic WebUI Operation Tools Tab — Virtual OSD When a menu option is modified through the Virtual OSD menu, the projector setting takes effect immediately. The Tools tab defaults to the secondary Virtual OSD tab. Selecting an option from a menu displays its associated window, showing related information and input fields.

  • Page 43: Admin Tab

    Basic WebUI Operation Admin Tab Under the Admin tab, select the System tab at the bottom of the window to upgrade, upload, backup and restore specific files, change gamma properties, and interrogate the projector (creating a zip file of information). Description The Upload feature allows you to select the file and file type you want to open.

  • Page 44: Upload A Gamma File

    Basic WebUI Operation Upload a Gamma File The projector must be powered On to enable the Upload drop-down list. 1. Select Gamma from the Upload drop-down list. Gamma files must have a .csv file extension with 1024 values (all colors same) or 1024 x 3 for individual colors.

  • Page 45: Perform Diagnostic Test

    Basic WebUI Operation Perform Diagnostic Test 1. Click Interrogate to initiate the diagnostic test and download the diagnostic test results to your computer. Once the download is complete, a File Download window appears. 2. Click Save to save the diagnostic test results file. Once the Interrogate function begins, you must allow it to run until completion.

  • Page 46: Advanced Tab - Real Time Events (Rte)

    Basic WebUI Operation Advanced Tab - Real Time Events (RTE) The RTE tab is where you can manage real-time events (i.e. add, delete, edit, copy and setup the GPIO). Add a Scheduled Event Scheduled events include a command or sequence of commands, for example, (PWR1) or (PWR1) (LSH1).

  • Page 47: Add A System Event

    Basic WebUI Operation Click Help for a description of special RTE commands available for adding loops and delays to the command sequence. 11. Click Test to run the entered command string. A green or red icon appears to the right side of the Test button to indicate whether the test passed or failed.

  • Page 48: Add A Function Key Event

    Basic WebUI Operation Add a Function Key Event 1. From the Advanced tab, click Add to open the RTE Wizard. 2. Select the Function Key Event tab. 3. Select a function from the drop-down list. Advanced Tab — Serial 1. From the Advanced tab, select the secondary Serial tab.

  • Page 49: Using The Ir Remote

    Using the IR Remote Laser radiation is emitted from the laser diode in the remote. Do not look directly into the laser beam. Failure to comply could result in minor or moderate injury. The IR remote is included with the User Kit (P/N: 130-103105-xx), which is shipped separately.

  • Page 50: Ir Remote Commands

    Using the IR Remote IR Remote Commands Power Press and hold the Power button for 2 seconds or press twice quickly to power the projector On or Off. Or, press and release the Power button followed immediately by the up arrow key (On) or the down arrow key (Off) to guarantee the correct action.
  • Page 51 Using the IR Remote Test Steps forward through all internal test patterns. After stepping past the last test pattern, the menu returns to the current input. Press Test and then cycle through the test patterns by pressing the left / right arrow keys. Press Exit to return to the current input. Proj Press Proj to display the current IP and projector number on screen.

  • Page 52: Select Inputs

    Select Inputs Select Inputs You can use the IR remote to setup your inputs; however, Christie recommends that inputs are setup through the WebUI. An input is an input source physically connected to the projector. Input describes the source signal to which it is connected.

  • Page 53: Working With Infrargb

    Working with InfraRGB Working with InfraRGB The InfraRGB menu allows you to configure the IR inputs and brightness. It allows you to select from a number of presets that define these proportions for different lighting conditions such as daylight, moonlight, starlight. These presets can be customized, but have factory default values. Basic InfraRGB Setup 1.

  • Page 54: Select Lighting Mode

    Working with InfraRGB Select Lighting Mode The lighting mode sets the RGB and IR brightness proportions. Choose the lighting mode to set the RGB and IR brightness for the RGB video source. A factor of 100 is the full brightness of the available video.

  • Page 55: Manage Infrargb With Irloc

    Working with InfraRGB Manage InfraRGB with IRLOC Matrix StIM™ WQ projectors use IRLOC to maintain the target IR brightness and target IR weight across an array of projectors. Adjust InfraRGB Across the Array from the Master Projector 1. From the Main menu, select InfraRGB > InfraRGB Target & Adjustments. 2.

  • Page 56: Setup Source Sequence

    Working with InfraRGB Setup Source Sequence InfraRGB can operate in the following 3 modes: • Simultaneous Mode: The RGB and IR signals are both taken from the main input. • InfraScene Mode: The RGB signal is taken from the main input and the IR signal is taken from the secondary input.

  • Page 57: Infrascene Mode

    Working with InfraRGB InfraScene Mode The output timing will be derived and locked to 1 of the 2 inputs (as specified by the frame lock option which can be either frame lock or frame lock secondary). For best performance (no frame skips or repeats) in Interleaved or InfraScene modes the 2 inputs should be synchronized together (gen-locked).

  • Page 58: Interleaved Mode

    Working with InfraRGB Interleaved Mode The output timing will be derived and locked to 1 of the 2 inputs (as specified by the frame lock option which can be either frame lock or frame lock secondary). For best performance (no frame skips or repeats) in Interleaved or InfraScene modes the 2 inputs should be synchronized together (gen-locked).

  • Page 59: Select A Lighting Mode

    Working with InfraRGB Select a Lighting Mode • Day light is 100% brightness of the RGB factor of the video source and 100% brightness of the IR factor. • To change the level of brightness of the lighting modes, see Change Brightness Levels of the Light Modes, on page 3-68.

  • Page 60: Reduce Motion Artifacts

    Reduce Motion Artifacts Reduce Motion Artifacts AccuFrame is used to reduce image artifacts, such as smearing and double image perception in high speed simulation environments. 1. From the Main menu, select Image Settings > AccuFrame. 2. Select Enable AccuFrame. 3. From the InfraRGB Source Sequence drop- down list select from: •...

  • Page 61: Arrayloc

    ArrayLOC ArrayLOC Matrix StIM™ WQ projectors use ArrayLOC to display a common gamut and brightness across an array of projectors. ArrayLOC monitors the projector array and adjusts settings automatically. The following section outlines how to manage color using ArrayLOC. ArrayLOC is enabled by default. Take Control of the Array Use this menu to set up array color and brightness.
  • Page 62 ArrayLOC A projector with Bright/ColorLOC mode disabled ignores BCLOC changes from the master projector. If at any point you are working with a slave projector you may not be able to change some settings as they will be locked (grayed out). To change which projector is the master check the Synchronize to This Projector option on another projector.

  • Page 63: Configure Bright/Colorloc

    ArrayLOC Configure Bright/ColorLOC This menu is used to configure the warning and minimum brightness and gamut thresholds. 1. From the Main menu, select ArrayLOC > Bright/ColorLOC Configuration to access and work with the capabilities of the projectors in the array. 2.

  • Page 64: Adjust Projected White And Primary Colors For The Array

    ArrayLOC Adjust Projected White and Primary Colors for the Array User-defined target color spaces allow color primaries and white points to be adjusted independently. For example, you can select the target color space User 1, copy the values from the target color space Factory, leave the color primaries, and adjust only the white point.
  • Page 65 ArrayLOC option. Only values for user defined white points (User White 1 through 4) can be changed. When Set White Color to Color Temperature is checked, the values are calculated based on the specified White Color Temperature. 5. Check the Set White to Color Temperature check box to recalculate Target White x/y values based on the specified standard White Color Temperature.

  • Page 66: Fine-Tune Whites, White Brightness, Or Primary Colors

    ArrayLOC Fine-tune Whites, White Brightness, or Primary Colors The Projector Color Adjustment menu lets you fine-tune color or brightness for individual projectors to accommodate any projector-specific optical elements (e.g. projection lens, fold mirrors, screen properties or ambient lighting). The following steps outline color adjustments using projector color settings until the colors appear to match the rest of the projectors in the array.

  • Page 67: Configure Arrayloc

    ArrayLOC Configure ArrayLOC Select the projector-to-projector communication network configuration for all Ethernet messages related to ArrayLOC functions, including ArrayLOC messages, and BCLOC messages. Make sure all projectors in an array are operating on the same network, either the Control Network or the ArrayLOC Network.

  • Page 68: Fine-Tune Projector Colors With A Color Meter

    ArrayLOC Fine-tune Projector Colors with a Color Meter To use a color meter for projector color adjustments, follow the instructions in Fine-tune Whites, White Brightness, or Primary Colors on page 54. Use the information below and a color meter for the XXX Part of YYY adjustments.

  • Page 69: Image Settings

    Image Settings Image Settings Adjust Gamma Settings To access the gamma settings for your secondary input select Input and Switching > Secondary Image Settings > Secondary Gamma Settings. To access the Gamma Settings, select Image Settings > Gamma Settings. The system offers 2 types of gamma correction.

  • Page 70: Gamma Function

    Image Settings graphics and video sources. The Standard curve (auto setup default) is a modified 2.22 curve with a small linear section in the black that enhances the detail in darker areas of the projected content. Typically Standard or 2.22 is used for all sources. Alternatively, if neither default is ideal, apply a simple gamma curve by defining a custom power function and slope.

  • Page 71: Configure The Display

    Configure the Display Configure the Display The Configuration menu provides access to diagnostics, calibration tools and the Service submenu (password- protected). Use this menu to define general operating parameters and communications with other projectors and equipment, and to access other advanced processing and image adjustments affecting overall performance.

  • Page 72: Actual Frame Delay

    Configure the Display Actual Frame Delay This control indicates the dynamically calculated, effective minimum frame delay for the projector. Power Management To access the Power Management menu select Configuration > Power Management from the main menu. Auto Power Up If there is an AC power interruption while Auto Power Up is enabled, the projector will resume operation in the same state as it left off.

  • Page 73: Fan Assist

    Configure the Display non-visible (IR) light. In this mode any visible light from the projector can noticeably reduce image contrast as seen through NVG devices. Fan Assist If necessary, use the slide bar to increase projector fan control. An increase to this setting will make the fans quicker to react and run at a higher intensity.

  • Page 74: Projector Address

    Configure the Display Serial Flow Control Determines whether software flow control or no flow control is used when transmitting and receiving data on the serial port. Serial Mode Select the serial data mode. The mode includes the number of bits, the parity and the number of stop bits.

  • Page 75: Ethernet Settings

    Configure the Display All Joined All messages reach all ports, regardless of type. In the case of multiple Ethernet sessions, input on one Ethernet session will be relayed to all other Ethernet sessions, as well as to the RS-232 and RS- 422 ports.

  • Page 76: Broadcast Keys

    Configure the Display Broadcast Keys Use Broadcast Keys to relay all key presses received by the projector to all other projectors on the network. Front IR Enabled Check this option to enable the front IR sensor. Wired Keypad Enabled Check this option to use the wired keypad. Display Error Messages Choose how you want to be notified of errors detected in either the incoming signal or projector.

  • Page 77: Freeze Light Engine Image

    Configure the Display Freeze Light Engine Image Check this option to freeze an incoming image on a single frame in order to examine details.  For example, in moving images it is sometimes difficult to observe artifacts such as external  de-interlacing/resizing and signal noise.

  • Page 78: Upgrade Software

    Upgrade Software Upgrade Software The upgrade package is a single file, which comprises all the firmware and software needed to operate the projector. The upgrade process updates the firmware files as necessary. Hardware that is up-to-date is not upgraded. Requirements •...
  • Page 79 CTRL+F5. If the message, Main update failed xxx, see log for details is displayed copy the upgrade log and send it to Christie technical support. Matrix StIM™ WQ/SIM WQ User Manual...

  • Page 81: Troubleshooting Guidelines

    • Read, understand, and observe all warnings and precautions when diagnosing and servicing. • If a solution cannot be found in this guide, contact your dealer for assistance. • A Christie accredited service technician is required when opening an enclosure to diagnose any probable cause. •...

  • Page 82: Status Display

    Status Display Status Display Projector status is indicated by a single 3-color LED adjacent to a 2-digit status display. Refer to the table below for a description of the variations that indicate operation status. A solid red LED indicates a system error and the corresponding error code indicates what the error is. Status 2-Character Display Description...

  • Page 83: Error Codes

    Error Codes Error Codes If the status display window shows any of the codes in the table below you may need a Christie accredited service technician to repair the component identified by the error code. Error codes are displayed in a 3-phase format: •...
  • Page 84 Error Codes Error Code Description (7-segment display) IR SAM Red driver Green driver Blue driver IR driver Red SAM Junction Temp Green SAM Junction Temp Blue SAM Junction Temp Fan Error Fan stall error (index number following tracks SST response IDs) Power supply fan SAM drive fan Intake fan...

  • Page 85: General Maintenance

    General Maintenance Cleaning the Lens Check periodically. A small amount of dust or dirt on the lens has minimal effect on image quality. To avoid the risk of scratching the lens, clean only if absolutely necessary. Remove Dust 1. Brush most of the dust from the lens with a camel-hair brush or blow dust away with a dust-free blower.

  • Page 87: Webui Menu Tree

    WebUI Menu Tree WebUI Menu Tree Matrix StIM™ WQ/SIM WQ User Manual 020-100883-01 Rev. 2 (06-2013)

  • Page 89: Serial Communication

    Serial Communication This document describes the serial communication protocol, consisting of ASCII text messages, used to control a Matrix StIM / SIM WQ projector remotely. Connection and Use Matrix StIM™ WQ/SIM WQ Specifications on page 127 for all cable requirements and other connection details.

  • Page 90: Basic Message Structure

    Serial Communication Message Formats Source Message format Function Examples From controller (Code Data) SET (set gamma function of main (BGF500) or (BGF 500) image to 222) (Code+Subcode Data) SET (set gamma function of image (BGF+SECD222) or to 222) (BGF+SECD222) From controller (Code ?) REQUEST (what is current gamma (BGF?) or (BGF ?) function?)

  • Page 91: Prefix Characters (Optional)

    Serial Communication Prefix Characters (optional) For acknowledgement that the projector has responded, and/or to maximize message integrity, insert one or two special characters before the 3-character Function code: Special Character Description Simple Acknowledgment, which will cause a ‘$’ character to be sent back from Maximize the projector when it has finished processing the message.

  • Page 92: Other Special Functions (Optional)

    Serial Communication Other Special Functions (optional) To add functionality to the current message, include one or more of the following special characters between the Function code/Subcode, and the first parameter. If more than one, add them in any order. See Flow Control on page 84.

  • Page 93: Text Parameters

    Serial Communication Text Parameters Most data is simply a numerical value, however some messages also require text. Enclose this text in double quotation marks, as in “Tilt the Wagon”. Use all characters as desired except for the following special characters shown in the left column below. These special characters require a 2-character combination.

  • Page 94: Specific Projector In A Network With 1 Controller

    Serial Communication Specific Projector in a Network with 1 Controller Message Format Function Example (Dest Addr Code Data) SET (turn projector #5 on) (5pwr1) ($Dest Addr Code Data) SET AND ACKNOWLEDGE MESSAGE (message ($5pwr1) processed?ffr55) Specific Projector in a Network with Multiple Controllers Message Format Function Example...

  • Page 95: Maximize Message Integrity

    Serial Communication Maximize Message Integrity For additional reassurance and/or maximum message integrity, you can insert one or two special characters: • Acknowledgements: If you want assurance from the projector (or group of projectors) that a set message has been processed, request an acknowledgement. An acknowledgement is returned after a message has been received and fully executed by the projector (i.e.

  • Page 96: Access Specific Inputs

    Serial Communication Access Specific Inputs For several commands (for example, BGC, Base Gamma Curve) you can direct the message to particular input or image. To do this, include a subcode after the function code. Example: (BGC 1) Select 2.22 gamma curve for main input. (BGC+MAIN 1) Select 2.22 gamma curve for main input.

  • Page 97: Network Operation

    Serial Communication Network Operation Up to 1000 projectors can be linked together in a chain with the ‘OUT’ port on one connected to the ‘IN’ port on the next. A controller connected to the ‘IN’ port on the first projector can control them all, either by broadcasting messages which have no address and are thus seen by all projectors, or by directing messages to specific projector addresses.

  • Page 98: Description Of Control Types

    Serial Communication Description Of Control Types Subclasses • Power Down Controls: These controls are accessible when the projector is in Standby power mode (i.e. power off) as well as when powered on. • Power Up Controls: These controls are only accessible when the system electronics are fully powered (not necessarily lamp on).

  • Page 99: Serial Command Reference

    Serial Command Reference Serial Command Reference Array Bright Color LOC (ABL) CONTROL GROUP: Preference SUBCLASS: Power Up ACCESS LEVEL: Operator Description This command is used to set parameters that control how the Array Bright/ColorLOC feature operates. From this control you enable the mode in which you want to operate the feature: target brightness, target gamut, update intervals, and other miscellaneous parameters.
  • Page 100 Serial Command Reference ALBV When set, all projectors in brightness group will use this projectors settings: 0 = OFF (normal) 1 = synchronize to group Note: A group can synchronize to only one projector. Setting ABL+ABLV on any projector in a group to make that projector the master projector releases the setting from any previous master projector in the group.

  • Page 101: Auto Color Enable (Ace)

    Serial Command Reference SITP Synchronize Test Pattern setting amongst array projectors. 0 = Independent 1 = Synchronized Examples: (ABL+MODE1) Enable Array Bright/ColorLOC. (ABL+MODE2) Disable Array Bright/ColorLOC. (ABL+BRGP 2) Set the brightness group to 2. (ABL+BRTG 400) Set the brightness target to 400 Lumens. Auto Color Enable (ACE) Preference Power Up...

  • Page 102: Accuframe (Acf)

    Serial Command Reference Accuframe (ACF) Preference Power Up Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Configure AccuFrame parameters. Used to reduce motion artifacts for simulation systems, specifically for night scenes. Will reduce brightness. The values represent draw-time in microseconds for RGB and IR. The remainder of the time in the frame will be dark time.

  • Page 103: Active Projector (Apj)

    Serial Command Reference Active Projector (APJ) Input Power Down Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Temporarily enable or disable the IR and wired keypad Inputs to a specific projector in a network of projectors. When a projector is disabled, the only key that works is PROJ. The next time the projector is powered up again, it will revert to fully enabled.

  • Page 104: Auto Shutdown (Ash)

    Serial Command Reference Auto Shutdown (ASH) Saved Power Down Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description When Auto Shutdown Mode has been selected, and no projector activity has been seen for the activation time-out period, the projector will enter a Power Saving mode in which the lamps will dim and the shutter close. If this condition persists for an additional time-out period the projector will automatically go to standby.

  • Page 105: Base Gamma Curve (Bgc)

    Serial Command Reference Base Gamma Curve (BGC) Input Power Down Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description This control lets you select the Gamma table. You can select from one of the standard tables, or select an arbitrary Gamma table that has been downloaded into the projector. A separate PC utility is needed to do this. The 2.22 table is a simple power curve.

  • Page 106: Base Gamma Slope (Bgs)

    Serial Command Reference Base Gamma Slope (BGS) Input Power Up Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Defines the slope to be used for the base custom Gamma table in the small linear section at the bottom of the curve. This slope can be used to bring the low level blacks in the image in or out. This slope, combined with the Gamma function, defines the custom Gamma table.

  • Page 107: Color Enable (Cle)

    Serial Command Reference Color Enable (CLE) Unsaved Power Up Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description This control allows the three primary colors (red, green, and blue) to be turned ON or OFF separately. It is used to look at the colors one at a time or in pairs when doing convergence, light measurements, etc. The list of values for this command are: 0 = White ...

  • Page 108: Error Message Enable (Eme)

    Serial Command Reference Error Message Enable (EME) Preference Power Down Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description This control enables the displaying of error messages, and determines to which interface the messages are sent. Error messages can be turned Of or can be sent out the serial port. This setting does not affect messages for invalid user entries, for which error messages are always displayed.

  • Page 109: Fan Assist (Fas)

    Serial Command Reference Fan Assist (FAS) Saved Power Down Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description This control is used to increase fan speed in environments with high ambient temperatures. Default of 0 will use normal fan speed control which should be sufficient under normal circumstances. To increase fan speed select larger values.

  • Page 110: Serial Flow Control (Flw)

    Serial Command Reference Serial Flow Control (FLW) Preference Power Down Advanced CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Set the flow control for a serial communications port. Subcode Description of Use PRTA Set the mode on port A (RS-232 IN) PRTB Set the mode on port B (RS-232 OUT) PRTC Set the mode on port C (RS-422)

  • Page 111: Gamma Correction (Gam)

    Serial Command Reference Gamma Correction (GAM) Preference Power Up Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description The Gamma Correction control is used to correct ambient conditions affecting the display. The Gamma control affects the shape of the curve determining what grey shades are displayed for a given amount of signal Input between minimum (black) and maximum (white).

  • Page 112: Serial Help (Hlp)

    Serial Command Reference Serial Help (HLP) Unsaved Power Down Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Query a list of all available serial commands, with brief descriptions and current enabled states. Subcode Description of Use <No Subcode > Request entire command Help listing, or list for a single command.

  • Page 113: Infrargb (Ifs)

    Serial Command Reference InfraRGB (IFS) Preference Power Up Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Configures InfraRGB lighting modes which defines the percentage of RGB and IR brightness. It allows selection of a number of presets that define these proportions for different lighting conditions such as daylight, moonlight, InfraRGB starlight.
  • Page 114 Serial Command Reference Examples: (IFS+SLCT 1) Enable InfraRGB. (IFS+ISLM 4) Select lighting mode preset 4 (moonlight). (IFS+RGBB ?) Get current RGB lighting brightness (percent * 10). (IFS+RGBB 250) Set RGB lighting brightness to 25%. (IFS+IRDB 1000) Set IR lighting brightness to 100%. (IFS+RGBX 500) Set RGB lighting brightness on User preset to 50%.

  • Page 115: Infrargb Coefficient (Irc)

    Serial Command Reference InfraRGB Coefficient (IRC) Preference Power Up Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Configures how IR is generated from RGB. The settings allow for either a factor or offset. There are a number of preset configurations and four user settings. The preset configurations cannot be modified, they default to factory settings.

  • Page 116: Irloc Configuration (Irl)

    Serial Command Reference Examples: (IRC+IRGB 1) Set InfraRGB preset to "All Channels". (IRC+REDC ?) Report the current Red Power. (IRC+IRGB 6) Set InfraRGB preset to "User 1". (IRC+GRN2 250) Set User 2 Green Power to 250. IRLOC Configuration (IRL) Unsaved Power Up Operator CONTROL GROUP:...

  • Page 117: Test Pattern Grey (Itg)

    Serial Command Reference Test Pattern Grey (ITG) Unsaved Power Up Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Specify the grey level to use for the 'Grey' flat field internal test pattern. Range 0-1023. The level defaults to 512 on power up. This command is on available while the grey test pattern is being displayed. Subcode Description of Use <No Subcode >...

  • Page 118: Keypad Ir Sensor Disable (Ken)

    Serial Command Reference Keypad IR Sensor Disable (KEN) Preference Power Down Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Enable or disable the IR or wired keypad sensors. You cannot disable the keypad that is currently being used. Subcode Description of Use FRNT Set to 1 to enable the front IR keypad sensor, 0 to disable WIRE...

  • Page 119: Logical Shutter (Lsh)

    Serial Command Reference Logical Shutter (LSH) Unsaved Power Up Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Turns OFF the LEDs in the projector to simulate a shutter operation. Subcode Description of Use <No Subcode > 0 Normal projection mode 1 Black (turns OFF light) Examples: (LSH 1) Turn Off the LEDs.

  • Page 120: Network Setup (Net)

    Serial Command Reference Network Setup (NET) Config/Preference Power Down Admin CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Set or request the network setup for this device. Subcode Description of Use DOMA Set the domain name ETH0 Set the IP address for the first ethernet controller. GATE Set the network gateway.

  • Page 121: Network Routing (Ntr)

    Serial Command Reference Network Routing (NTR) Preference Power Down Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Set routing for ASCII messages. Subcode Description of Use <No Subcode > Used to enable or disable daisy chaining. 0 = RS-232, RS-422 & Ethernet communications are all separate from one another 1 = RS-422 port(s) is/are connected to the RS-232 network 2 = The Ethernet port is connected to the RS-232 network...

  • Page 122: Projector Color Adjustment (Pca)

    Serial Command Reference Projector Color Adjustment (PCA) Unsaved Power Down Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Allows ArrayLOC projector-specific color adjustments ("tweaks") to be set. Subcodes ROxR - BOxW have a small 'x' listed. The small 'x' represents the color table being edited. Different color tables, denoted by 'x' - replace 'x' with the following: ...

  • Page 123: Projector Hours (Pjh)

    Serial Command Reference SAVE Saves current set of adjustments as factory defaults. WBAJ White Brightness Adjustment COPY Copy data setting from a referenced table to the selected one. Example: Projector Hours (PJH) Unsaved Power Down Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Reports the number of hours elapsed on the projector.

  • Page 124: Ping (Png)

    Serial Command Reference PING (PNG) Configuration Power Down Status CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description This command returns basic projector information to the user which includes the type of device & main software version. Note that some devices have multiple CPUs each with its own software version. Only the software version of what is considered to be the master CPU, is returned here.

  • Page 125: Power (Pwr)

    Serial Command Reference Power (PWR) (PWR) Power Unsaved Power Down Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Change the power state of the projector. Possible values: 0 - Power-OFF 1 - Power-ON 10 - Projector is cooling down. (Read-only) 11 - Projector is warming up. (Read-only) Subcode Description of Use <No Subcode >...

  • Page 126: Advanced Color Setting (Rgb)

    Serial Command Reference Advanced Color Setting (RGB) Preference Power Up Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Adjusts native projector color space by adjusting the LED power levels. This can be used when ColorLOC is disabled or if ColorLOC is running in Native or Fixed mode. Care should be exercised when adjusting these settings as it is possible to overdrive the LEDs and may cause the projector to perform a safety shutdown.

  • Page 127: Real Time Events (Rte)

    Serial Command Reference Real Time Events (RTE) Unsaved Power Down Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Real time events allow custom user actions to occur based on a system trigger. There are various triggers in the system such as power up, input change, errors, or based on time. Time can be absolute, (e.g. 12:00:00 on December 25, 2008) or relative (e.g.
  • Page 128 Serial Command Reference GPIO Events: (RTE G "AAAAAAA" "description" "command") where A is GPIO Input for each pin: = X (don't care) = H (when pin is high) - See on page = L (when pin is low) - See on page Delete All Events: (RTE X *)

  • Page 129: Select Input (Sin)

    Serial Command Reference GPIO Events: (RTE G "XXXXXXX" "description" "(PWR 1)") Turn ON the projector if we receive any GPIO Input. (RTE G "" "description" "(PWR 1)") Turn ON the projector if we receive any GPIO Input. (RTE G "XX" "description" "(PWR 1)") Turn ON the projector if we receive any GPIO Input. (RTE G "XXXXXLH"...

  • Page 130: Screen Orientation (Sor)

    Serial Command Reference Screen Orientation (SOR) Preference Power Up Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Selects the orientation of the displayed image. It can be displayed normally, inverted horizontally, inverted vertically, or inverted in both directions, as required by the projector installation. Valid values are:  0 = Front Projection ...

  • Page 131: Target Color Space (Tcs)

    Serial Command Reference Target Color Space (TCS) Preference Power Up Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description This command is used to set the ArrayLOC target gamut. Several preset color spaces are provided in addition to four user setting gamuts. The control subcodes provide access to all the presets. Due to the large number of sub-codes they are not all listed.

  • Page 132: Time/Date (Tmd)

    Serial Command Reference Examples: (TCS+SLCT 1) Select EBU color gamut as target.  (TCS+RDCX 290) Set current Target gamut red x point to 0.290. (TCS+BLEY ?) Return value of EBU preset blue y point. (TCS+COPY 3) Copy settings from HD Video to current. Time/Date (TMD) Preference Power Down...

  • Page 133: Target White Point (Twp)

    Serial Command Reference Target White Point (TWP) Preference Power Up Operator CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description This command is used to set the ArrayLOC target white-point. Several preset white points are provided in addition to four user setting white points. The control subcodes provide access to all the presets. Due to the large number of sub-codes they are not all listed.

  • Page 134: User Id (Uid)

    Serial Command Reference User ID (UID) Unsaved Power Down None CONTROL GROUP: SUBCLASS: ACCESS LEVEL: Description Allows users to login to the serial interface. Subcode Description of Use <No Subcode > Examples: (UID "username" "password") Login a user.  (UID) Logout the current user, also happens automatically when a new user logs in.  (UID?) Display the current logged in user and their access level (UID!"username"...

  • Page 135: Gpio Port

    GPIO Port This section explains how to use a GPIO link from the projector to external equipment, such as devices for 3D synchronizing. The GPIO connector located on the input panel provides a flexible method of interfacing a wide range of external I/O devices to the projector. There are 7 GPIO pins available on the 9 pin D-Sub GPIO connector, which are configurable via RS-232 commands.

  • Page 136: Configure Gpio

    GPIO Port Configure GPIO The GPIO connector can be configured to automate any number of events using the serial command code GIO. See General Purpose Input/Output (GIO) on page 99. Each pin is defined as either an input or output depending on the desired outcome. Configure the pin as an input if you want the projector to respond to something the device does and as an output if you want the external device to respond to an action taken by the projector.
  • Page 137 RS-422 RS-422 Pins Pin # Signal Direction Pin 1 Pin 2 RXD- Pin 3 TXD- Pin 4 RXD+ Pin 5 TXD+ Pin 6 Pin 7 Pin 8 Pin 9 +12V (500mA) Matrix StIM™ WQ/SIM WQ User Manual 020-100883-01 Rev. 2 (06-2013)

  • Page 139: Matrix Stim™ Wq/Sim Wq Specifications

    Inputs / inputs • On-board Ethernet control capabilities outputs, • Additional Ethernet connections for Christie ArrayLOC™ network control and • IR/wired remote control as part of optical user kit networking • 2 x RS-232 ports and 1 x RS-422 port •...
  • Page 140 • Auto power up • Menus in 5 languages • Christie AccuFrame™ smear reduction technology, fully adjustable in 1 % increments to min hold time of <6ms • Christie ArrayLOC — automatic, continuous management of brightness and color space levels of all projectors in the array to a common level, in real- time •...

  • Page 141: Matrix Stim™ Wq/Sim Wq User Manual

    Each offset is specified with the other at zero. Simultaneous horizontal and vertical offsets may limit the adjustment range of each. StIM WQ and SIM WQ are both available with a Ruggedized Motion Platform kit. These are purpose built to interface with customers' motion platform structures and available on a build-to-order basis. For details, please contact your Christie sales representative.
  • Page 143 *000-103893-01* ASSY TECH DOCS Matrix StIM™ WQ/SIM WQ...
  • Page 144 Corporate offi ces Worldwide offi ces USA – Cypress United Kingdom Eastern Europe Singapore Japan ph: 714-236-8610 ph: +44 118 977 8000 ph: +36 (0) 1 47 48 100 ph: +65 6877-8737 ph: 81-3-3599-7481 Canada – Kitchener France Middle East Beijing South Korea ph: 519-744-8005...

This manual is also suitable for:

Matrix sim-wq130-002103-01130-003104-01

Table of Contents