Section 1 Introduction Christie DS+5K/5Kc/8K, HD5K/5Kc/8K/8Kc, Projector Mirage S+2K/4K/8K, DW3K/3Kc/6K/6Kc, Matrix Overview S+2K/4000/HD4K, DLV1400-DX and DLV1920- DX are all professional 3-chip projectors based on next-generation Digital Light Processing™ (DLP™) technology by Texas Instruments™ to deliver high quality, crisp, clean images.
Warranty Registration If you encounter any problems with the projector and require assistance, contact your dealer or Christie Digital Systems. Fill out the information in the table below and keep with your records for future reference. Purchase Record Dealer:...
Page 8
Downloaded from ProjectorsManual.com Manuals...
Section 2 Installation & Setup The instructions provided here are for those that are familiar with the projector and Quick Setup wish to quickly set it up and use it temporarily. Refer to the remaining subsections of this manual for a more complete setup. Step 1 Install a Projection Lens The projection lens is shipped separately from the projector and must be installed...
Page 10
Section 2: Installation and Setup Step 4 Connect the Line Cord The North American-rated line cord is provided with each projector. Ensure that you are using a line cord, socket and power plug that meets the appropriate local rating standards. Plug the line cord to the AC receptacle located on the right hand side of the projector and the three-pronged end into a grounded AC outlet.
Section 2: Installation and Setup Proper installation of your projector will ensure the quality of your display. Whether Installation you are installing a projector temporarily or permanently you should take the Considerations following into account to ensure your projector performs optimally. Installation type Choose the installation type that best suits your needs: front or rear screen, floor mount or inverted mount.
Page 12
Section 2: Installation and Setup Rear screen installations There are two basic types of rear screens: diffused and optical. A diffused screen has a surface, which spreads the light striking it. Purely diffused screens have a gain of less than one. The main advantage of the diffused screen is its wide viewing angle, similar to that of a flat screen for front screen projection.
Page 13
Section 2: Installation and Setup output with a 4:3 aspect ratio onto a 10-foot (3m) high screen, the width of the screen must be at least 13.3feet (4m). Ambient Lighting The high brightness of this projector is well suited for locations where ambient lighting might be considered less than ideal for projection.
Page 14
Section 2: Installation and Setup Vertical and horizontal position The correct vertical and horizontal position of the projector in relation to the screen depends on the lens type and the screen size. Ideally, the projector should be positioned perpendicular to the screen. This way, the image will appear rectangular instead of keystoned (trapezoidal).
Page 15
Section 2: Installation and Setup Figure 2.1. Vertical Offset Examples 013-100199-04 2-7. Downloaded from ProjectorsManual.com Manuals...
Page 16
Section 2: Installation and Setup Figure 2.2. Lens Vertical Offsets 013-100199-04 Downloaded from ProjectorsManual.com Manuals...
Page 17
Section 2: Installation and Setup The horizontal position of the image can be offset – that is moved to the left or right of lens center, by adjusting the fully motorized lens mount through software. The amount of horizontal offset available depends on the lens installed and if the image has already been vertically offset.
Page 18
Section 2: Installation and Setup Figure 2.4. Lens Horizontal Offsets 2-10 013-100199-04 Downloaded from ProjectorsManual.com Manuals...
For more information, contact your dealer. Use only the CHRISTIE approved ceiling mount kit designed for your projector. Refer to the installation instructions and safety guidelines provided in the kit.
Section 2: Installation and Setup Sources connect to the Input Panel located at the back of the projector. See Figure 2.6. Connecting The upper right corner ( ) typically accepts an RGB signal from an external Sources INPUT 1 analog RGB source, or it can also be used for YPbPr signals or additional video sources.
Page 21
Section 2: Installation and Setup Figure 2.7. Connecting RGB and Sync NOTES: 1) If for some reason the projector fails to recognize a signal as an RGB signal, specify this Color Space option within the Image Settings menu. See 3.5 Adjusting the Image.
Page 22
Section 2: Installation and Setup Composite and S-Video provide simultaneous connection of both a composite video INPUT 3 INPUT 4 source ( ) and an S-Video source ( ). See Figure 2.9. INPUT 3 INPUT 4 Figure 2.9.Connecting Composite or S-Video sources DVI Digital Video Use the DVI-I connector at to connect either analog or digital video devices...
Section 2: Installation and Setup As an alternative to the projector’s keypad or remote, you may wish to communicate Connecting with the projector using a PC or other controller. Such a device sends commands and Communications receives feedback via serial links (RS232 and RS422), Ethernet or GPIO communications to the projector, all described below.
Page 24
Section 2: Installation and Setup Figure 2.11. Connecting RS422 Ethernet Communications Ethernet Communications To add the projector to an existing Ethernet network with other equipment such as controllers and other projectors, connect standard CAT5 Ethernet cable between your Ethernet controller (or hub) and the Ethernet port on the side of the projector. Upon connection to an Ethernet network, the projector’s factory default IP address of 0.0.0.0.0 will automatically enable the DHCP function (if available on the network) to assign a new IP address that is valid and unique for that network.
Page 25
Section 2: Installation and Setup Figure 2.12. RS232 Network : To control multiple projectors with a computer/controller having an MIXED NETWORK RS422 interface, first set them all to the same baud rate as your RS422 controller. NOTE: You must enable this combination of RS422 and RS232 in the Communications menu.
Page 26
Section 2: Installation and Setup : To add one or more projectors to an Ethernet network, ETHERNET NETWORK SETUP use standard CAT5 cable to connect each projector’s Ethernet port to a hub belonging to the network. A controller or PC must also be connected to the hub. See Figure 2.14. Figure 2.14.
Section 2: Installation and Setup The Subnet Mask and Default Gateway are SUBNET MASK AND DEFAULT GATEWAY: automatically assigned when DHCP is enabled. If a static IP is being used, it must be assigned before the subnet mask. The Default Gateway is an optional router device used to send and receive data outside the subnet.
Section 2: Installation and Setup The North American rated line cord is provided with each projector. Ensure Power that you are using a line cord, socket and power plug that meets the Connection appropriate local rating standards. Plug the line cord to the AC receptacle located at the back of the projector, below the input panel, and the three-pronged end into a grounded AC outlet.
Section 3 Operation This section explains how to effectively operate the projector once it has been About the installed. It is recommended that you read this section and familiarize yourself with Projector the components and the available menu options before you begin using your projector for the first time.
Section 3: Operation Lens Mount & The projector is built with a motorized lens mount that allows for easy lens control Projection Lenses and adjustment. This includes such functions as adjusting vertical and horizontal offsets, zoom and focus. The lens mount can be fitted with any one of the available optional lenses –...
Section 3: Operation Laser radiation is emitted from the laser diode in the remote. Do not look Using the directly into the beam of the remote. Remote or Built-In Keypad Keypad Commands The projector is typically controlled using one of the following keypads: •...
Page 32
Section 3: Operation *These are toggle keys, which require you to press and hold or press twice or press and use the up/down arrow keys. NOTE: To turn the OSD off you must press Figure 3.2. Remote Keypad 013-100199-04 Downloaded from ProjectorsManual.com Manuals...
Page 33
Section 3: Operation Wired Remote You can convert the IR remote into a wired remote keypad using the cable provided with the projector. Connect one end into the remote and the other to the mini stereo connector on the input panel labeled as .
Page 34
Section 3: Operation Table 3.1. Auto Setup What an “Auto Setup” Does OPTIMIZES: SETS TO DEFAULT: Pixel Tracking Contrast Pixel Phase Brightness Size and Blanking Auto Input Level (off) Vertical Stretch Detail (if video source) Position Filter Input Levels Luma Delay NOTE: You must have an unlocked channel present to use Auto Setup.
Page 35
Section 3: Operation Input 6 Input 6 Press to display from the interface module installed in the Option 2 slot. INPUT 6 Input 6 NOTE: If you have the optional Dual SD/HD-SDI Module installed and there are two INPUT 8. inputs connected here, the second input (B) is considered If you are using the INPUT 6...
Page 36
Section 3: Operation OSD (On-screen display) Press to hide the projector’s menu system during use. To see the menus again, do one of the following: • Press and hold for two seconds • Press and release followed immediately by • Press Invisible menus are fully functional, enabling “hidden”...
Page 37
Section 3: Operation The “Projector” checkbox (read-only) shows whether or not the projector physically connected to a keypad is listening to commands from that keypad. A checkmark means that connected projector is listening; if there is no checkmark, you are communicating with a different projector.
Section 3: Operation Lens Shift NOTE: Use the key (built-in keypad) with the general keys to get the same effect as if using the arrow keys related to “Lens V” or “Lens H” on the IR remote. Laser Press to activate the laser pointer on the remote.
Page 39
Section 3: Operation On-line Help If at any time you are uncertain what to do next, press to display summary Help information about the current menu or highlighted option. Press again to exit. In Help addition, a line of “hint” text is included at the bottom of some menus. Press from the presentation level to access general Help Topics.
Page 40
Section 3: Operation Once selected, change the setting as desired (see below) and press to save and return to the current function menu. Slide bars in menus – The current value for a given parameter, such as size or vertical stretch, appears to the left of its slide bar icon (adjustment window).
Page 41
Section 3: Operation Example of Pull-Down List If you prefer to quickly scroll through a list without first pulling it down, highlight the option and use . Press when the desired choice appears. NOTES: 1) Press to jump between pages in an extra long pull-down list. 2) Press while in a pull-down list to cancel any change.
Section 3: Operation Editing Numerical Values Enter numbers directly from the keypad in order to specify numbers representing projectors, channels (source setups), or slots. As each digit is entered, it is displayed and the cursor moves on. Note that channel numbers are defined with two digits—for example, if you enter only a single digit (such as “7”) for a channel number, the channel will automatically be defined as “07”.
Page 43
Section 3: Operation previously through the same input location. Once you have adjusted a display parameter, such as pixel tracking or contrast, all current settings are collectively stored in the projector's memory as a unique two-digit channel, such as . You can have numerous distinct channels available for the same input, any of which can be selected by using the key on the keypad followed by the two-digit channel...
Page 44
Section 3: Operation NOTES: 1) The current channel is highlighted upon entering the channel list, or, if this channel is not displayed here, the first channel in the list is highlighted. 2) Channels created automatically do not appear in the channel list unless a parameter for the channel has been changed.
Page 45
Section 3: Operation Table 3.2. Abbreviations for Signal Type Abbrev. Signal Type Composite (4 wire) on HC input Composite (4 wire) on V input Sync-on-green Separate H,V Separate H,V swapped SVid S-Video CVid Composite Video Digital To copy, delete or edit a channel, FUNCTIONS WITHIN THE CHANNEL SETUP MENU —...
Page 46
Section 3: Operation Figure 3.5. Deleting a Channel highlight any channel in the Channel Setup menu TO DELETE MULTIPLE CHANNELS and press to go to the Channel Copy/Delete submenu. Select “Delete Unlocked Func Only” and press to delete all unlocked channels. Select “Delete All Channels” to delete all channels, even those that are locked.
Section 3: Operation NOTES: 1) If you enter a channel number that already exists, a dialog message appears indicating that this number is already in use–assign a different channel number. 2) You can define up to 50 channels. • 1-8, corresponding to where on the projector’s input panel the source is INPUT: connected.
Page 48
Section 3: Operation NOTES: 1) To hide these “direct” slide bars, disable the “Display Slide bars” checkbox in the Menu Preferences menu. 2) To hide the entire menu system from view, turn off the on-screen display by pressing Before You Begin Use Auto Setup ( Auto For a good and efficient first step in perfecting the image, press...
Page 49
Section 3: Operation Position, V-Position or Blanking do not correspond to those for a preset. This option is not offered in the Resize Presets pull-down list. • Select for most sources (factory default). The image will be centered “DEFAULT” and displayed as large as possible depending on the type of source. •...
Page 50
Section 3: Operation • Select to display an anamorphic “ANAMORPHIC” image in its native 16:9 aspect ratio. The image will fill the screen from side-to-side and be centered between black bars at top and bottom. 3-22 013-100199-04 Downloaded from ProjectorsManual.com Manuals...
Section 3: Operation Size “Size” controls both the image width and height in tandem, maintaining the current aspect ratio (proportion) of the displayed signal data. Vertical Stretch “Vertical Stretch” adjusts the height of the image while keeping the width constant. Use “Vertical Stretch”...
Page 52
Section 3: Operation NOTE: The value shown represents where the approximate center of the image lies in relation to the total number of pixels available vertically. This varies widely according to the signal—watch the image while adjusting. Advanced Size and Position —...
Page 53
Section 3: Operation Figure 3.6. Blanking of a PIP Image By default, a Plug & Play PLUG & DISPLAY (EDID): (EDID) source outputs a signal according to the EDID information provided by the projector. To override this information and display in a different format (for example, if your Plug &...
Page 54
Section 3: Operation NOTE: If the environment lighting changes, an adjustment of Gamma is recommended (see below). Brightness Press Bright d adjust the slide bar.) SHORT CUT: “Brightness” increases or decreases the amount of black in the image (0-100). For best results, keep close to 50.
Section 3: Operation Detail “Detail” adjusts the sharpness of a video image so that edges remain clearly defined. It can be particularly useful if a significant “Noise Reduction” adjustment has caused the image to appear too soft. Adjust until the display is as sharp as desired, keeping in mind that because “Detail”...
Page 56
Section 3: Operation Automatic Gain Control (AGC) affects decoded video ENABLE DECODER AGC: images only. Enter a checkmark (default) in most instances—this activates the decoder’s AGC circuit to ensure properly bright images. Delete the checkmark if a decoded video image exhibits strange color artifacts such as stripes in highly saturated colors, indicating an incompatibility between this source and the AGC.
Page 57
Section 3: Operation This slide bar adjusts the color saturation level, i.e., the amount of color in a COLOR: video image. Lower settings produce less saturated colors — for example a setting of “0” produces a black and white image. If the color level is too high, colors will be overpowering and unrealistic.
Page 58
Section 3: Operation NOTES: 1) Input levels apply for the current source only, but for any color temperature used. 2) Assuming that color temperature has been set up based on the internal test patterns, you can then set up input levels for a given source so that it matches the color temperature of the internal test patterns.
Page 59
Section 3: Operation pulse from the normal back porch location (which is likely too short) to the tip of the horizontal sync pulse. Tri Level is typically needed for an HDTV source. Select which color or colors you want to see in the display, useful COLOR ENABLE –...
Page 60
Section 3: Operation Figure 3.7. Adjusting Input Levels Using the Peak Detector (RED EXAMPLE SHOWN) Advanced Image Settings — SUBMENU Use the Advanced Image Settings submenu to make the adjustments necessary for lesser- used but more specialized applications on your projector. This control applies a default video, graphics or simple gamma table GAMMA TABLE: or “curve”...
Page 61
Section 3: Operation In “Select Color Adjustment”, SELECT COLOR ADJUSTMENT: choose an overall color palette for all images. The “Max Drives” factory default simply drives all three colors at their maximum level so that they are fully on and cannot be changed.
Page 62
Section 3: Operation Simulation 3D — SUBMENU OF ADVANCED IMAGE SETTINGS Use the options in the Simulation 3D menu to make the timing adjustments necessary for realistic simulation and 3D images. NOTES: 1) Available in Mirage projectors only. 2) For complete 3D application notes, refer to the separate Using 3D in Mirage manual provided with the Mirage projector.
Page 63
Section 3: Operation With your sync cable, Z-screen and, if desired, emitter connected as described in the Using 3D in Mirage manual, select the option suited to your 3D configuration (see above). If Frame Delay is two (or 0), do not invert; if frame delay is one or three, invert.
Section 3: Operation For static images with no motion, such as graphics from a CD. STILL: For video images that did not originate from film, or for moving MOTION: computer-generated images. For video images that originated from film. This will optimize image quality FILM: and stability.
Page 65
Section 3: Operation Auto Power-up Enter a checkmark to enable the projector to automatically power up after losing power due to a power failure or due to unplugging the projector during operation. Note that unsaved display adjustments may be lost. Set Date &...
Start-up And No Signal – A splash screen appears at start-up only if there is no source signal. To replace the default “Christie logo” splash screen (or other) with one of your own, use KoRE Librarian to download the desired .bmp to the projector. This will overwrite the current splash screen content in projector memory.
Page 67
Section 3: Operation Select “Separate” (factory default) to keep RS232, RS422 and Ethernet SEPARATE: messages on their respective paths instead of being broadcast to the other types of ports. In Figure 3.8A, RS422 controls only the projector to which it is connected. In Figure 3.8B, either RS232 or RS422 will control the network.
Page 68
Section 3: Operation Enter a valid and unique IP address for use on the network to which the IP ADDRESS: projector is currently connected. This address will overwrite any previous IP address such as the projector’s factory-defined default (0.0.0.0), or one that has been assigned by a DHCP server or other user.
Section 3: Operation DMX Channel Function Value 0 – 64 Open Base Shutter 65 – 192 No Action 193 – 255 Closed 0 – 254 Locked Base + 1 Slider Lock Unlocked * Base + 2 Input * 1 – 8 Input # Base + 3 Channel *...
Page 70
NOTE: If the optional ChristieTWIST module is installed, this option is Keystone and Warping, and activates a submenu for defining custom image shapes. Please refer to documentation included with your Christie TWIST module. Use to correct a keystoned image shape in which both sides of your image are inclined toward the top or bottom edge.
Page 71
Uniformity function, delete the “Uniformity Enable” checkmark. NOTES: 1) See also 3.10, Using Multiple Projectors for the complete step-by-step procedure for achieving uniform brightness in adjacent displays. 2) If Christie TWIST module is installed, the enable checkbox changes to a list giving the option to choose from several different uniformity maps.
Page 72
Section 3: Operation In some cases, you may find that none of the pre- DEFINING “USER” COLOR GAMUTS: defined “Select Color Adjustment” options exactly suit your needs. For example, you may require a unique color gamut (range) for a single projector or application, or you may need to precisely match colors across multiple adjacent displays.
Page 73
Section 3: Operation Figure 3.10. CIE 1931 Chromaticity Diagram (without Yellow Notch Filter) NOTE: Keep new x,y coordinates within the original color gamut triangle shown here. PROCEDURE FOR X,Y ADJUSTMENTS: See 3.10, Using Multiple Projectors. Use this submenu COLOR SATURATION: if you do not have specific color coordinates in mind and will simply judge color performance by eye or...
Page 74
Section 3: Operation hardware, by matching up black level hues with a “target area” hue (the intersection of the center lines), and adjusting the overlaps (edges) surrounding the target area. NOTES: 1) Refer to section 3.10, Using Multiple Projectors for additional information.
Page 75
Section 3: Operation Freeze Image Enter a check mark to freeze (stop) an image on a single frame. This diagnostic tool is useful if you need to examine in detail a still version of an incoming image that cannot be “frozen” at the source. For example, in moving images it is sometimes difficult to observe artifacts such as external de-interlacing/resizing and signal noise.
Section 3: Operation NOTES: 1) Adjust offset before gain, since offset affects gain. 2) A value of 128 represents no change in normal odd pixel offset or gain. 3) Odd Pixel Adjustment eliminates “one pixel on, one pixel off” artifact only, not any type of larger artifacts. Reserved No function.
Page 77
Section 3: Operation LiteLOC™ Calibration NOTES: 1) LiteLOC™ Calibration takes up to two minutes. 2) For best results, allow the projector to warm up for 15 minutes prior to calibration. LiteLOC™ Calibration defines the range of power needed to maintain lamp brightness.
Section 3: Operation PIP (Picture-in-Picture) and Seamless Switching are independent but related projector Working with features that both utilize two image-processing paths within the projector. In the case PIP or of Picture-in-Picture, this double processing enables you to display two different Seamless images simultaneously –...
Page 79
Section 3: Operation Swap Main and PIP Image Toggle the current picture-in-picture relationship so that the primary (main) image becomes secondary (PIP), and the secondary image becomes primary. Swapping is available only when PIP is enabled. NOTE: There may be a slight delay when swapping the Primary and Secondary images.
Section 3: Operation PIP Border Color Select the desired color for the PIP window border. NOTES: 1) Numbers 7 and 8 on the Picture-in-Picture and Switching submenu control switching parameters. 2) Disable PIP in order to work with Seamless Switching. 3) Disable PIP and Best Switching for Interlaced sources > 35kHz. Working with Seamless Seamless Switching is the ability to instantly and/or smoothly switch sources, and is Switching...
Section 3: Operation Numbers Select Main Image Use Numbers Select Main Image to use the numeric keys #1-8 as input keys. This remapping of the keypad (see right) can be particularly useful with PIP displays, providing a convenient shortcut for changing the primary (background) image without first having to return to the Main menu.
Page 82
Section 3: Operation NOTES: 1) If you change modes over the life of a lamp, the lamp limit you originally expected may no longer be possible. 2) Turning the lamp on and off reduces lamp life significantly, as do other factors. 3) It is recommended that Lamp Limit not exceed the expected lamp life, otherwise a lamp could become dangerously fragile with overuse.
Page 83
Section 3: Operation NOTE: The number shown for “intensity” is not the actual lumen output, but rather a correlated value only—1246 may represent 3500 lumens, for example. To use “ ” mode, judge by eye (or use a meter) and set the level as desired for Intensity your application.
Page 84
Section 3: Operation to record the serial number for a newly installed lamp: CHANGE LAMP In the Lamp S/N window, use the number text entry keys to record the new lamp serial number and press again to accept the change. See Using Slide bars and Other Controls if you need help entering the number.
Section 3: Operation The read-only Status menu lists a variety of details about the standard and optional Status Menu components currently detected in the projector. Refer to the Status menu for versions of hardware and software installed, the type (size) of lamp, the hours logged in total and for a specific period (such as a rental period), and for your projector model name and serial number.
Section 3: Operation To return to the factory-set color primaries, such as when a projector is moved to different site, you must access the Service menu (password-protected). Select the “Reset to Factory Defaults?” option in the Color Primaries submenu. Then repeat the calibration process describe above, if desired, and continue with matching of colors.
Page 87
Section 3: Operation Figure 3.14. Copy X/Y Values into All Projectors 6. In each projector, judge by eye and adjust x/y coordinates slightly in the following manner: • To match reds, decrease “Red X” until full field red screens match. •...
Page 88
Section 3: Operation Using the Color Saturation Menu for Color Matching You may prefer to use the Color Saturation menu to match colors across multiple screens. In the three Color Adjustment submenus (Red, Green, Blue—see right), set all main values to 100 and the secondary values to 0.
Page 89
Section 3: Operation Light output and Brightness Uniformity can vary RUN LAMP FOR 100 HOURS— significantly during the first 100 hours of lamp use. For best results with new lamps, either set up Brightness Uniformity after this period, or do an initial setup and re-check at 100 hours.
Page 90
Section 3: Operation In either Color Adjustments menu, select a “User” color. Then: • If you have created a “User 1” color gamut (recommended) for a well- matched wall, continue to Step 1e. • If you prefer maximum brightness rather than a particular color temperature, select “Max Drives”.
Page 91
Section 3: Operation Figure 3.16. Match Zones to Center Color Temperature Repeat the color adjustment of sides and corners for each edge of the screen that does not yet match the center (note that each corner is adjustable in either of its two adjacent “side”...
“Uniformity Enable” checkbox at the top of the Brightness Uniformity menu. Edge Blending Christie Edge Blending is an innovative set of software functions that can quickly and easily blend white levels along the edges of multiple adjacent projected images to create a single seamless larger image.
Page 93
Section 3: Operation • determines how much area is used for blending along an overlapping Blend Width edge. Slide bar values represent the number of eight-pixel steps used for the blend. For example, a setting of “eight” creates a blended edge 24 pixels wide. A setting of “0”...
Page 94
Section 3: Operation • turns your Show Blending Overlap defined blend width area to solid gray so that, if needed, simply overlapping the gray bars can seamlessly align two adjacent images. Toggle the Show Blending Overlap off to reactivate the blend effect.
Page 95
Section 3: Operation : On one projector, increase the Blend Width for an overlapping SET BLEND WIDTH edge (for example, if the projector’s image is on left, its right edge overlaps the adjacent image—adjust Right Blend Width). Use the same setting on the second projector for this shared edge.
RS422 port (recommended), or open an Ethernet socket (i.e., Telnet) between your controller and the valid projector address. Valid ASCII codes and messages are documented in the Christie Serial Communications document available at the Christie website. Connect your PC to the projector’s Ethernet port. In your web VIA WEB INTERFACE —...
Section 3: Operation Repeat for remaining networked projectors as desired. Keep in mind that multiple units can be controlled from one PC, but each unit will be in its own ChristieNET interface (web browser) at the PC. Likewise, you can make up to five separate web locations to a single projector.
Page 98
Section 3: Operation No Signal The message "No signal" occurs when there is no source signal detected at the selected input—both HSYNC and VSYNC are inactive and the screen background is black. Connect or correct the signal, or try another input. Bad Sync The message "Bad Sync"...
Page 99
GENERAL Software bug. Contact dealer/factory. CRC error in flash ROM. Download new software. Engineering-only programming is complete. Call Christie, replace TIPM. Attempting to download code without being in boot mode Invalid interrupt. Power off/on. If it persists, contact dealer/factory. User forced system to stay in boot mode...
Page 100
Section 3: Operation Red modular Formatter communication failure Green modular Formatter communication failure Blue modular Formatter communication failure Modular formatter architecture error Modular formatter DMD mismatch Modular formatter sequence mismatch MISCELLANEOUS Unable to program the optional module Unable to power the optional module Unable to program the Dual Slot Backplane Module (DSBP) Unable to program the optional Post Processing Module (Warp module) Exit...
Section 4 Maintenance The projector is an international regulatory agency approved product designed for safe Warnings and and reliable operation. To assure complete safety at all times it is important to Safety acknowledge the following precautions while operating the projector. Guidelines WARNING Always power down the projector using appropriate procedure...
Page 102
Sudden stops, excessive force and uneven surfaces may cause the projector and cart combination to overturn. • Only use Christie-approved ceiling mount fixture, if the projector is to be ceiling mounted. Lamp Lamp: The projector uses a Cermax® Xenon lamp to deliver its high brightness. A lamp should be replaced when it has reached its end of life (1000 hrs, typical) or if a noticeable change in brightness occurs.
Page 103
The projector has been dropped or the shipping case (if applicable) has been badly damaged. WARNING Do not attempt to service the projector yourself. All servicing must be performed by Christie accredited service technicians. Use replacement parts that are manufacturer-approved only. Use of any other part other than the ones specified...
Replacement procedure later in this section. Filters REPLACE: Do not reuse old filters. Use the Whenever a lamp is replaced or sooner filter provided in the Christie Lamp and if required Filter Kit. Covers (External) As required CLEAN: Clean dust from external covers using a clean, lint free cotton cloth as required.
Lamp and Filter back of the projector (below the input panel) and can be accessed by removing the Replacement lamp access panel. Use only the Christie approved Lamp and Filter Kit for your specific projector model. See Table 4.2 below. 013-100199-04 4-5.
Page 106
A qualified service technician must perform lamp replacement. Cool the lamp completely and handle by the housing only. Install the correct wattage lamp supplied by Christie (see above) and read the Lamp Replacement procedure in its entirety before proceeding. Do not touch the glass surface of the lamp. Fingerprints left on the surface can lead to an intense accumulation of heat called a “hotspot”, which could...
Page 107
Section 4: Maintenance 1. TURN THE LAMP OFF Press (power) to turn the lamp off. Allow the cooling fans to stop automatically (within approximately five minutes) before proceeding with Step 2. This wait period is also required to allow the lamp to sufficiently cool before handling.
Page 108
Section 4: Maintenance 5. REMOVE THE LAMP MODULE Firmly grasp the lamp by its housing only and pull it straight out (lamp slides along guides) until it is free. See Figure 4.4. Discard the lamp using safe disposal/recycling practices. Figure 4.4. Remove Lamp Module 6.
Page 109
Section 4: Maintenance NOTE: If you can’t turn the lamp lock into position, it is likely the lamp is not fully inserted. In this case, partially remove the lamp and try pushing it back in again. Then, try switching the lock lever to the “lock” position. 8.
If you are working in an extremely dusty environment you may want to replace the filters sooner. Use the filters provided in the Christie approved Lamp and Filter Kit for your specific projector model. 1. TURN OFF THE PROJECTOR, COOL and UNPLUG Before removing or installing a filter, turn off the projector and allow it to cool for five minutes before unplugging.
Section 4: Maintenance A variety of lenses can accommodate different throw distances and specific types of Replacing the installations. Refer to Section 6 - Specifications for details. To change a lens, follow Projection Lens the steps below. No tools are required for “compact” lenses shown. STEP 1 Turn off the projector, cool and unplug NOTE: If necessary, a lens can be swapped out while the projector is running, but...
Page 112
Section 4: Maintenance STEP 3 Rotate the lens Rotate the lens counter-clockwise until the tabs are free from the lens retainer ring. See Figure 4.10A. NOTE: The connector slide assembly allows the connector to move as the lens is rotated. STEP 4 Pull lens out Lens connectors will disconnect when...
Section 5 Troubleshooting If the projector does not appear to be operating properly, note the symptoms present and use the following guide to assist you. If you cannot resolve the problems yourself, contact your dealer for assistance. NOTE: A qualified service technician is required when opening the projector to diagnose any “probable cause”. Displays Symptom The projector is on but there’s no display...
Page 114
Section 5: Troubleshooting Symptom The upper portion of the display is waving, tearing or jittering… 1. This can sometimes occur with video or VCR sources. Check your source. CAUSE / REMEDY: Symptom Portions of the display are cut off or wrap to the opposite edge… 1.
Section 5: Troubleshooting Symptom The display is “noisy”… 1. Display adjustment at your input source may be required. Adjust pixel tracking, CAUSE / REMEDY: phase and filter. Noise is particularly common on YPbPr signals from a DVD player. (If using a PC source, adjust using a high-frequency test pattern with one pixel on/off throughout.) 2.
Page 116
Downloaded from ProjectorsManual.com Manuals...
6.1 Specifications Specifications apply to all models unless otherwise noted. Display Resolution SXGA+ (1400 x 1050) for DS+5K-5Kc-8K/MirageS+2K-4K-8K/Matrix S+2K/4000/DLV1400-DX HD (1920 x 1080, widescreen) for HD5K-5Kc-8K /Matrix HD4K/DLV1920-DX HD2 (1280 x 720, widescreen) for DW3K-3Kc/DW6K-6Kc Achievable Brightness (* all values +/-10%)
Section 6: Specifications Colors and Gray Scale Resolution 10 bits Displayable colors 1.1billion Color Temperature Default 5800K +950K/-650K HD Default 6300K +/- 500K Range of Adjustment (see Note 1) 3200K – 9300K ™ NOTE 1: Via electronic controls, with Comprehensive Color Adjustment turned off.
Page 119
Section 6: Specifications Sync (Interlaced or Progressive Scan Format) Horizontal Frequency Range 31 – 120 kHz Vertical Frequency Range (See Note 3) 23.97 – 150 Hz Sync Type Separate H and V, direct or swapped Composite (bi-level, tri-level, XOR, OR) Sync-On-Green/luma (bi-level, tri- level)
Page 120
Section 6: Specifications GPIO Connector Type One male 9-pin Dsub Number of I/O lines (each individually assignable as input or output) Power Output +12VDC @ 200mA max. Output sink current (logic low) 100mA @ 1V Ethernet Connector Type One female RJ45 Maximum throughput 115.2kbps Remote Control...
Page 122
Section 6: Specifications EMC Emissions FCC CFR47, Part 15, Subpart B, Class A — Unintentional Radiation CISPR 22: 1997 / EN55022: 1998 — Radio disturbance characteristics for ITE EMC Immunity CISPR 24 / EN55024:1998 (all parts of immunity characteristics for ITE) Operating Environment Temperature 5°C to 35°C (41°F to 95°F)
Appendix A Glossary This appendix defines the specific terms used in this manual as they apply to this projector. Also included are other general terms commonly used in the projection industry. Active Line Time The time, inside one horizontal scan line, during which video is generated. Ambient Light Rejection The ability of a screen to reflect ambient light in a direction away from the “line of best viewing”.
Page 124
Appendix A: Glossary adjustable display settings, etc. Use channels to switch between a variety of setups quickly, automatically recalling previously defined display parameters. Channel List A list/menu of previously defined channels available in projector memory. Channel Number A number that uniquely identifies a specific channel retained in projector memory. The projector can retain up to 99 channels.
Appendix A: Glossary Diffused Screen A type of rear-projection screen which spreads the light striking it. Screen gain is less than one but audience viewing angles are increased. Display Setting An adjustment that affects the display of an image. Such display settings include contrast, brightness, tint, blanking, size, offsets, and others.
The Line of Best Viewing is along the line of reflection. LiteLOC A Christie software feature where samples of output light from a projector trigger ™ automatic adjustments in the lamp ballast power in order to maintain a constant light output over time.
Page 127
Appendix A: Glossary Menu A list of selectable options displayed on the screen. NTSC Video A video output format of some video tape and disk players. There are two types of NTSC (National Television Standards Committee) video: NTSC 3.58 and NTSC 4.43. NTSC 3.58 is used primarily in North America and Japan.
Page 128
Appendix A: Glossary Retrace Time The minimum time required for a CRT projector to move the position of the scanning (Horizontal) spot from the right edge to the left edge. Rise Time The time required by the video amplifier of the projector to increase its output from 10% to 90% of the maximum value.
Page 129
(usually 75Σ for video). Throw Distance The distance between the front feet of the projector and the screen. Also called “Projector-to-Screen Distance”. Always use the correct Christie throw distance formula to calculate the proper throw distance (±5%) required for your lens. Throw Ratio Throw ratio = throw distance / screen width.
Page 130
Downloaded from ProjectorsManual.com Manuals...
Appendix B Keypad Reference NOTE: The IR remote is a standard component provided with the projector. Use the extension cable also provided to convert the IR remote to a wired remote, if desired. Refer to Section 3 for a specific description of each key and how to use them correctly.
Page 132
Downloaded from ProjectorsManual.com Manuals...
Appendix C Serial Communication Cables A serial link of RS232 or RS422 enables ASCII communication with the projector so that it can be controlled remotely from a PC or other controller. From a PC, connect a standard nine-wire RS232 serial cable to the port.
Page 134
Downloaded from ProjectorsManual.com Manuals...
Page 135
Appendix D Throw Distance Calculating Throw Distance It is important throw distance be precisely calculated for your installation using the appropriate formula from the chart below. To calculate throw distance you must know the screen size and the lens type installed in the projector. In general, the larger you want the image to be the greater the distance you must allow between the lens and...
Page 145
Appendix D: Throw Distance HD Lenses 0.67:1 Fixed Lens Image Image Width Throw Diagonal Distance Throw Distance Formula (TD) Inch Inch Inch TD = 0.7058 x W + 2.23 Where W = image width (inch) 66.9 169.8 58.3 43.4 110.1 67.8 172.1 59.1...
Page 146
Appendix D: Throw Distance 1.1:1 FP Fixed Lens Image Image Width Throw Throw Distance Formula Diagonal Distance (TD) Inch Inch Inch TD = 1.145 x W + 3.76 (inch) Where W = image width 114.7 291.4 100.0 254.0 118.3 300.4 122.0 309.8 106.3...
Appendix E System Integration The GPIO (General Purpose Input Output) connector located on the input panel provides a flexible method of interfacing a wide range of external I/O devices to the projector. There are seven GIO pins available on the nine-pin D-Sub GPIO connector, which are configurable via RS232 commands. The other two pins are reserved for ground and power –...
Appendix E: System Integration Query Command (GIO?) Request the state and configuration of all pins (GIO! “HHLLHLH” “OOIOOOI”) Reply of pin state and configuration (GIO? C2) Request configuration for pin #2 (GIO! C2 O) Reply with pin #2 configuration as output (GIO? 2) Request the state of pin #2 (GIO! H)
Appendix F Optional Input Modules There are many optional input modules and accessories currently available for this projector. Contact your dealer for a complete and up-to-date listing. RGB500 Input Module The RGB500 Input Module may be installed in this projector, a Marquee Signal 38-804606-xx Switcher, or a Marquee Case/Power Supply.
Appendix G: Index RGB400 Active Loop-Thru The RGB400 ALT Input Module may be installed in this projector, a Marquee Signal Input Module Switcher, or a Marquee Case/Power Supply. The module receives analog RGB input 38-804607-xx signals from computers or other RGB source devices. Video inputs are 75 Ω...
Page 167
Appendix G: Index Features • Supports Digital Visual Interface (DVI) single-channel • Supports VESA® Extended Display Identification Data (EDID™) • Provides an active-loop-through using a DVI connector (conforming to the DVI Specification) Serial Digital Input Module The module accepts a serial digital 4:2:2 component video signal (YCbCr) via a single 38-804602-xx BNC connector.
Page 168
Downloaded from ProjectorsManual.com Manuals...
Page 169
Index Name, 18 Number, 15, 19 Signal Type, 16 3D Simulation, 34 Channel Copy/Delete, 17 3D Stereo Sync, 34 Channel Edit Menu, 18 Channel Key, 6, 15 Channel Selection, 15 Ambient Lighting, 5 Channel Setup Menu, 16 Anamorphic, 22 And Enter Key, 17 Arrow Keys, 9 And Function Key, 17 Auto Input Level, 30...
Page 170
Appendix G: Index Custom Sizing, 20 Geometry and Color, Submenu, 42 Glossary of Terms, 1 Dark Interval, 34 Date and Time Help Setting, 37 Context-sensitive, 11 Decoder AGC Horizontal Position, 23 Enabling, 28 Decoder Luma Delay, 29 Detail Image Threshold, 36 Brightness, 26 Diagnostics and Calibration, Submenu, Contrast, 25...
Page 171
Appendix G: Index Wired, 5 Menu Key, 7 Keystone Menu Location on Screen, 37 Correcting, 42 Menu Navigation, 10, 19 Motion Filter, 35 Multiple Projectors Description, 57 Lamp, 2, 4 Failure to Ignite, 3 History, 55 Hours, 53 Network Routing, 39 Hours of Use, 56 Network, Split.
Page 172
Appendix G: Index Mounting, 11 Split Networks Number, 14 Options for Setup, 19 Quick Setup, 1 S-Video Resetting, 70 Connection, 14 Projector Height, 11, 1 Swap Main and PIP Image. See PIP Projector Key, 8 Switcher, 19 Pull-Down Lists, Use of, 12 Sync Def.