Tx Hdmi Input 1 And 2 Ports; Rx Hdmi Output 1 And 2 Ports; Tx Hdmi Output 1 And 2 Ports; Overview - Lightware UBEX-PRO20-HDMI-F110 User Manual

 
     
5. Front Panel LCD Menu Operations 5. Front Panel LCD Menu Operations
5.3.1. TX HDMI Input 1 and 2 Ports
HDMI Input
The HDCP setting and information about the HDMI inputs are
displayed:
▪ HDCP enable - Enabled / Disabled
▪ +5V present
▪ Signal present
Active resolution
▪
▪ Total resolution
▪ Color space
Video Settings
The following settings can be set in the case of both input ports:
▪ #scaler #frc
Resolution mode
– Passthrough: pass-through mode; the original resolution of
the stream is transmitted.
– Forced: the resolution which is set in the Resolution setting
menu is forced.
▪ Resolution setting - select a resolution to force from the pre-
installed list. The entire list can be found in the
the Scaler / FRC section.
Image position - Center / Fit / Stretch
▪

INFO: The Image position setting on the HDMI IN 2 port is a read-
only parameter and fixed as "Center".
▪ Color space - Passthrough / Force RGB / Force YCbCr 4:4:4 /
Force YCbCr 4:2:2 #csc #colorspace
Stream Output
The following settings and information are related to the video stream
sent toward the remote RX endpoint:
▪ Stream enable - Enabled / Disabled
▪ Signal present
▪ Active resolution
▪ Total resolution
Color space
▪
5.3.2. RX HDMI Output 1 and 2 Ports
INFO:

to the remote output ports of the receiver.
Stream Input
#hdcp
The following information is displayed in the case of both streams
transmitted to the receiver:
▪
▪
▪
▪
▪
HDMI Output
The following information is displayed in the case of both output ports
of the receiver:
▪
▪
▪
Resolutions of
▪
▪
5.3.3. TX HDMI Output 1 and 2 Ports
The following information is displayed for both local output ports:
▪
▪
▪
▪
▪
▪
#streamenable
▪
#hdcp #power5v
Applied F-series endpoint firmware package: v1.4.1 | Applied R-series endpoint firmware package: v1.4.1 | LDC software: v1.34.0b2
UBEX series – Extender Application Mode – User's Manual UBEX series – Extender Application Mode – User's Manual
The following port status information and settings are related
Stream source - Stream 1 / Stream 2 #switch #crosspoint
– The source stream of HDMI outputs in the receiver can be
switched in this submenu.
Signal present
Active resolution
Total resolution
Color space
Hotplug detect
Signal present
Active resolution
Total resolution
Color space
HDCP mode - Auto / Always
Output 5V mode - Always on / Auto / Always off
Hotplug detect
Signal present
Active resolution
Total resolution
Color space
5.3.4. Overview
The current status of the input and output
ports is summarized in the Overview menu.
The icons display information about the port
and the incoming/transmitted signals.

TIPS AND TRICKS: Press enter on the
selected port for the settings and detailed
status information.
Icon Icon is blue (inactive) Icon is white (active)
 Sink is not connected Sink is connected
 Signal is not present Signal is present
Signal is not encrypted with Signal is encrypted with

HDCP HDCP
No audio signal in the video Audio is embedded in the

stream video stream
5.4. Ports Menu - Receiver Mode
The most important settings and status
information of the HDMI output ports are
available in the Ports menu.
Select the desired output port and enter to
see the submenus.
The following port diagrams help to identify and navigate to the
desired submenu:
Port diagram - Receiver mode
50 50