Local Trx O2 Port; Overview; Edid Menu; View - Lightware UBEX-PRO20-HDMI-F110 User Manual

 
     
5. Front Panel LCD Menu Operations 5. Front Panel LCD Menu Operations
5.5.5. Local TRX O2 Port
The following information is displayed for the local output port:
▪ HDCP mode - Auto / Always #hdcp
▪ Output 5V mode - Always on / Auto / Always off
▪ Hotplug detect
▪ Signal present
▪ Active resolution
▪ Total resolution
▪ Color space
5.5.6. Overview
The current status of the local and remote
input/output ports is summarized
the Overview menu. The icons display
information about the port and
transmitted signals.
TIPS AND TRICKS:
Press enter on the
selected port for the settings and detailed
status information.
Icon Icon is blue (inactive)
 Sink is not connected
 Signal is not present
Signal is not encrypted with

HDCP
No audio signal in the video

stream
5.6. EDID Menu
Advanced EDID Management is available
in the front panel LCD menu which allows
to view an EDID, switch, or save it to the
User EDID memory. See more information
about EDID technology in EDID Management
section. The EDID memory structure of
the device can be found in Advanced EDID
Management section. #edid
5.6.1. View
Select the desired EDID memory block:
Factory EDIDs, Last attached EDIDs, User
EDIDs, or Emulated EDIDs (only in case of the
transmitter). Select the Name item and press
the knob. Use the jog dial to step between
the EDIDs. The following information can be
checked:
▪
▪
▪
5.6.2. Switch
in
INFO:

The submenu looks similar as the View
the
submenu but in this case, the Destination
is also listed. To change an EDID do the
following steps:
Step 1. Navigate to the EDID / Switch submenu.
Step 2. Select the Source EDID item and press
Icon is white (active)
Step 3. Select the Destination item and press the knob. Use the jog dial
Sink is connected
Signal is present
Step 4. Navigate to the Switch option and press the knob.
Signal is encrypted with
HDCP 5.6.3. Save
Audio is embedded in the The EDID of a connected sink can be saved
video stream to the User EDID memory as follows:
Step 1. Navigate to the EDID / Save submenu.
Step 2. Select the Source EDID item and press
Step 3. Select the Destination item and press the knob. Use the jog dial
Step 4. Navigate to the Save option and press the knob.
Applied F-series endpoint firmware package: v1.4.1 | Applied R-series endpoint firmware package: v1.4.1 | LDC software: v1.34.0b2
UBEX series – Extender Application Mode – User's Manual UBEX series – Extender Application Mode – User's Manual
Preferred Resolution
Monitor Name
Audio Info
The Switch menu is available in the Transmitter mode only.
the knob. Use the jog dial to select the
desired EDID (F1-F144, U1-U12, or D1-D4) and press the knob.
to select the desired EDID memory (E1-E2, All) and press the
knob.
the knob. Use the jog dial to select
the desired EDID (D1-D4) and press
the knob.
to select the desired EDID memory (U1-U12) and press the
knob.
5.7. System Status Menu
The most important status information is
displayed about the extender in the menu.
#status
Device Info
Hardware- and software-related information are listed in the submenu,
e.g. device label - this is a user defined unique name which can be set
in the LDC software (see the details in the
LW3 protocol command (see the details in the
section), and serial number, firmware version, etc.
Link Status
The current status of the optical or DAC connection, advanced
information about the installed SFP+ modules, and the bonding state
are available under the menu.
Operation
The uptime and the operation time can be read out from the menu.
Temperatures
The recent temperature of the CPU, the system, and the FPGA are
displayed in the menu.

ATTENTION! If the front panel Status LED blinks, check the
temperatures under this menu and ensure the correct air flow for
the device.
Voltages
The recent voltages of the device are displayed in the menu.

WARNING! If the front panel Status LED blinks, power off the
device immediately.
53 53
Status Tab section) or with
Set the Device Label
#firmwareversion