Ubex-Pro20-Hdmi-F110 - Transceiver Mode; Release Notes Of The Firmware Packages; Release Notes - Lightware UBEX-PRO20-HDMI-F110 User Manual

 
     
12. Appendix 12. Appendix
12.5.6. UBEX-PRO20-HDMI-F110 - Transceiver Mode
General
Application mode selection setting
Crosspoint settings
Video stream switch state, Audio stream switch state
HDMI input port
Video port name, HDCP setting
Stream settings
Enable/disable status, Color space conversion setting
Scaler settings
Enable/disable status, Resolution setting, Image position
Color space conversion setting
Frame rate converter (FRC) settings
Enable/disable status, Resolution setting
Color space conversion setting
HDMI output ports
Port name, HDCP mode, Power +5V mode, Color depth setting
No sync screen mode, No sync screen color
Analog audio input port
Port name, Volume, Balance, Gain settings
Analog audio output port
Port name, Mute state, Volume, Balance, Gain settings
Ethernet ports
Enable/disable status, Mode setting
Static IP address, Network mask, Gateway address
DHCP status (enable / disable)
RS-232 port
Port name, Command injection status, Command injection port nr.
Baud rate, Data bits, Parity, Stop bits
Infrared ports
Port name, Command injection port nr.
Miscellaneous settings
Device label, Control lock status
Display brightness, Jog dial rotary direction, Fan setting
User EDID data (U1-U12), Emulated EDIDs by ports
UBEX series – Extender Application Mode – User's Manual UBEX series – Extender Application Mode – User's Manual
12.6. Release Notes of the Firmware Packages
12.6.1. Release Notes
v1.4.1b2
Release date: 2019-12-03
Bugfix:
▪ Fixed a glitch with input scaler configuration storage
▪ Optimized runtime memory usage
v1.4.0b4
Release date: 2019-11-27
New feature:
▪ Added check to refuse downgrading to earlier versions
Bugfix:
▪ Added file system in order to cope with bad NAND flash blocks
▪ Improved stability for multicast update
v1.3.2b2
Release date: 2019-08-14
New feature:
▪ Fixed issues with using the 10.0.0.0/8 IP range for control
v1.3.1b5
Release date: 2019-07-02
New feature:
▪ Added support for No Sync Screen generation on TX/TRX sources
(for network diagnostics)
▪ Added support for LDC Orientation Preference setting
▪ Improved LLDP support (reporting operation mode and package
version)
▪ Added identify() method to S and O nodes
▪ Fixed channel status data for analog audio inputs
▪ Refined fan control (silent operation)
▪ Added support for R100 part numbers
▪ Added support for IR in F110
▪ Added support for centralized firmware update
Applied F-series endpoint firmware package: v1.4.1 | Applied R-series endpoint firmware package: v1.4.1 | LDC software: v1.34.0b2
Bugfix:
▪ Fixed a glitch with some 10G switches not switching streams
automatically
Known issue:
▪ Video output is unstable when scaling a pre-cropped image to
4K@60
v1.3.0b10
Release date: 2019-05-03
New feature:
▪ Added support for Transceiver mode
▪ Added support for scaling to the default resolution of the
attached display (EDID-based scaling)
▪ Added support for F110 variant (analog audio in/out, RS-232)
▪ Added support for upgrading endpoints in matrix mode with
LDU2
Bugfix:
▪ Signal properties are reported on unconnected outputs as well
▪ All RX/TX mode related settings are cleared when operation
mode is changed
▪ Fixed issues with fan control
▪ Added support for LW3 configuration backup and restore
▪ Fixed issue with color space conversion for DVI inputs
▪ Fixed a glitch with updating dynamic EDIDs
▪ Improved stability of the embedded bootloader
v1.2.0b1
Release date: 2018-10-05
Bugfix:
▪ Fixed issue with detecting HDMI 1.x sources after receiving
4K@60 Hz
▪ Fixed 4K@30 Hz transmission over a single 10G link
▪ Fixed image artifacts with a few scaling configurations
v1.1.1b1
Release date: 2018-08-30
Bugfix:
▪ More robust SCDC handling is introduced.
135 135